- 您現在的位置：買賣IC網 > PDF目錄375845 > FM24C128 (Fairchild Semiconductor Corporation) The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each PDF資料下載
參數資料
| 型號： | FM24C128 |
| 廠商： | Fairchild Semiconductor Corporation |
| 元件分類： | DRAM |
| 英文描述： | The CAT24FC02 is a 2-kb Serial CMOS EEPROM internally organized as 256 words of 8 bits each |
| 中文描述： | 該CAT24FC02是一個2 KB的EEPROM的國內256個8位每字舉辦的串行CMOS |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 102K |
| 代理商： | FM24C128 |
8
www.fairchildsemi.com
FM24C128 Rev. B.1
F
Pin Descriptions
Serial Clock (SCL)
The SCL input is used to clock all data into and out of the device.
Serial Data (SDA)
SDA is a bi-directional pin used to transfer data into and out of the
device. It is an open drain output and may be wire
–
ORed with any
number of open drain or open collector outputs.
Write Protect (WP)
If tied to V
CC
, PROGRAM operations onto the entire memory will
not be executed. READ operations are possible. If tied to V
,
normal operation is enabled, READ/WRITE over the entire memory
is possible.
This feature allows the user to assign the entire memory as ROM
which can be protected against accidental programming. When
write is disabled, slave address and word address will be acknowl-
edged but data will not be acknowledged.
This pin has an internal pull-down circuit. However, on systems
where write protection is not required it is recommended that this
pin is tied to V
SS
.
Device Selection Inputs A2, A1 and A0 (as
appropriate)
These inputs collectively serve as
“
chip select
”
signal to an
EEPROM when multiple EEPROMs are present on the same IIC
bus. Hence these inputs should be connected to V
CC
or V
SS
in a
unique manner to allow proper selection of an EEPROM amongst
multiple EEPROMs. During a typical addressing sequence, every
EEPROM on the IIC bus compares the configuration of these
inputs to the respective 3 bit
“
Device/Page block selection
”
information (part of slave address) to determine a valid selection.
For e.g. if the 3 bit
“
Device/Page block selection
”
is 1-0-1, then the
EEPROM whose
“
Device Selection inputs
”
(A2, A1 and A0) are
connected to V
CC
-V
SS
-V
CC
respectively, is selected.
Device Operation
The FM24C128 supports a bi-directional bus oriented protocol.
The protocol defines any device that sends data onto the bus as
a transmitter and the receiving device as the receiver. The device
controlling the transfer is the master and the device that is
controlled is the slave. The master will always initiate data
transfers and provide the clock for both transmit and receive
operations. Therefore, the FM24C128 will be considered a slave
in all applications.
Clock and Data Conventions
Data states on the SDA line can change only during SCL LOW.
SDA state changes during SCL HIGH are reserved for indicating
start and stop conditions. Refer Figure 1.
Start Condition
All commands are preceded by the start condition, which is a
HIGH to LOW transition of SDA when SCL is HIGH. The FM24C128
continuously monitors the SDA and SCL lines for the start condi-
tion and will not respond to any command until this condition has
been met. Refer Figure 2.
Stop Condition
All communications are terminated by a stop condition, which is a
LOW to HIGH transition of SDA when SCL is HIGH. The stop
condition is also used by the FM24C128 to place the device in the
standby power mode. Refer Figure 2.
FM24C128 Array Addressing
During Read/Write operations, addressing the EEPROM memory
array involves in providing 2 address bytes,
“
Word Address 1
”
and
“
Word Address 0." However on FM24C128 only the 6 least
significant bits (LSB) of
“
Word Address 1
”
byte are used in
decoding the access location. The remaining 2 bits are not used
and are recommended to be set to
“
0." All 8 bits of the
“
Word
Address 0
”
byte are used in decoding the access location.
相關PDF資料 |
PDF描述 |
|---|---|
| FM24C16U | 16K-Bit Standard 2-Wire Bus Interface Serial EEPROM(16K位的標準兩線控制總線接口串行EEPROM) |
| FM24C256-SE | 256Kb FRAM Serial Memory |
| FM24C256LZYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256FLZYYX | 256 KBit 2-Wire Bus Interface Serial EEPROM with Write Protect |
| FM24C256 | 256K-Bit 2-Wire Bus Interface Serial EEPROM with Write Protect(帶寫保護的256K位的兩線控制總線接口串行EEPROM) |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FM24C128EMT8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| FM24C128EMT8X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| FM24C128EMW8 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| FM24C128EMW8X | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:I2C Serial EEPROM |
| FM24C128EN | 功能描述:電可擦除可編程只讀存儲器 RoHS:否 制造商:Atmel 存儲容量:2 Kbit 組織:256 B x 8 數據保留:100 yr 最大時鐘頻率:1000 KHz 最大工作電流:6 uA 工作電源電壓:1.7 V to 5.5 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 |
發布緊急采購，3分鐘左右您將得到回復。