參數資料
型號： FLATRONL1810B(LB800H-UL)18LCD
英文描述： Monitor_ICs:BA033FP-E2 BA7657F CAT24WC08J-TE13 FDC6326L GM5020 KIA7042AF M12L16161A-7T RC1117S-2.5 S524A40X21(SCT0) THC63LVD823
中文描述： Monitor_ICs：BA033FP - E2類BA7657F CAT24WC08J - TE13 FDC6326L GM5020 KIA7042AF M12L16161A -航路RC1117S - 2.5 S524A40X21（SCT0）THC63LVD823
文件頁數： 46/52頁
文件大?。?/td> 6610K
代理商： FLATRONL1810B(LB800H-UL)18LCD
ADJUSTMENT
- 14 -
GENERAL INFORMATION
All adjustment are thoroughly checked and corrected
when the monitor leaves the factory, but sometimes
several adjustments may be required.
Adjustment should be following procedure and after
warming up for a minimum of 30 minutes.
Alignment appliances and tools.
- IBM compatible PC.
- Programmable Signal Generator.
(eg. VG-819 made by Astrodesign Co.)
- EPROM or EEPROM with saved each mode data.
- Alignment Adaptor and Software.
- Digital Voltmeter.
- White Balance Meter.
- Luminance Meter.
- High-voltage Meter.
AUTOMATIC AND MANUAL DEGAUSSING
The degaussing coil is mounted around the CDT so that
automatic degaussing when turn on the monitor. But a
monitor is moved or faced in a different direction, become
poor color purity cause of CDT magnetized, then
press
DEGAUSS on the OSD menu.
ADJUSTMENT PROCEDURE & METHOD
-
Install the cable for adjustment such as Figure 1and run
the alignment program on the DOS for IBM compatible PC.
-
Set external Brightness and Contrast volume to max position.
1. Adjustment for B
+
Voltage.
1) Display cross hatch pattern at Mode 4.
2) Adjust voltage to 175V
±
0.5Vdc with
VR901
.
2. Adjustment for High-Voltage.
1) Display cross hatch pattern at Mode 4.
2) Adjust Anode voltage to 26kV
+
0.1kV, 26kV-0.2kV
with
VR701
.
3. Adjustment for Factory Mode (Preset Mode).
1) Display cross hatch pattern at Mode 1.
2) Run alignment program for FB775B on the
IBM compatible PC.
3) Power button of the monitor turn off
→
turn on.
4) COMMAND
→
START
→
Y(Yes) command.
5) DIST. ADJ.
→
TILT command.
6) Adjust tilt as arrow keys to be the best condition.
7) DIST. ADJ.
→
BALANCE command.
8) Adjust balance of side-pincushion as arrow keys to
be the best condition.
9) DIST. ADJ.
→
BALANCE command.
10)
Adjust parallelogram as arrow keys to be the best
condition.
11)
DIST. ADJ.
→
FOS. ADJ command.
12)
Adjust V-SIZE as arrow keys to 230
±
2mm.
13)
Adjust V-POSITION as arrow keys to center of the
screen.
14)
Adjust H-SIZE as arrow keys to 310
±
2mm.
15)
Adjust H-POSITION as arrow keys to center of the
screen.
16)
Adjust S-PCC (Side-Pincushion) as arrow keys to be
the best condition.
17)
Adjust TRAPEZOID as arrow keys to be the best
condition.
18)
Display from Mode 1 to Mode 4 and repeat above
from number
12)
to
17)
.
19)
PRESET EXIT
→
Y (Yes) command.
4. Adjustment for White Balance and Luminance.
1) Set the White Balance Meter.
2)
Press the DEGAUSS on the OSD menu for demagnetization
of the CDT.
3) Set Brightness max and SUB-Brightness to 200
(Decimal) position.
4) Display color 0,0 pattern at Mode 4.
5) COLOR ADJ.
→
LUMINANCE command of the
alignment program.
6) COLOR ADJ.
→
BIAS ADJ. command of the
alignment program.
7) Check whether blue color or not at R-BIAS and
B-BIAS to min position and G-BIAS to 150(decimal)
to adjust Sub-Brightness to 0.2±0.05FL of the raster
luminance. Check it's not blue color.
8) Adjust R-BIAS and B-BIAS command to x=0.283
±
0.02 and y=0.298
±
0.02 on the White Balance Meter
with PC arrow keys.
9) Adjust SUB-Brightness command to 0.3
±
0.1FL of the
raster luminance.
10)
Display color 15,0 box pattern (70x70mm) at Mode 4.
11)
Set Contrast max and SUB-Contrast to max position.
12)
DRIVE ADJ command.
13)
Set G-DRIVE to 160(A0) (decimal) at DRIVE of the
alignment program.
相關PDF資料
PDF描述
FLATRON18LCD882LE(LS882C-UA) Monitor_ICs:BA7657F SIL161 AD9884 MX88L282
FLATRON775FT(FB775BC)17COLOR Monitor_ICs:FB775B LTV-817M STR-F6654A[LF1351]
FLATRON795FT(FB795CE)17COLOR Monitor_ICs:FB775B LTV-817M STR-F6654A[LF1351]
FLATRON795FTPLUS(FB795CU)17COLOR Monitor_ICs:FB775B LTV-817M STR-F6654A[LF1351]
FLB Series Flash Memory Card 2 MB Through 40 MB (AMD Based)(2M字節-40M字節閃速存儲器卡（基于AMD）)
相關代理商/技術參數
參數描述
FLAT-WASHER-.506X.620X.020 制造商:ITT Interconnect Solutions 功能描述:
Flavus 2.4GHz Reference board 功能描述:天線 Reference Board for Flavus 2.4 GHz RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W
FLAVUS-GSM-REFERENCE-BOARD 功能描述:天線 Reference Board for Flavus GSM Antenna RoHS:否 制造商:Molex 技術類型:Cellular Antenna 頻率: 帶寬: 尺寸:106.7 mm L x 13 mm W
FLAX500R00A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Precision Resistor (Conformally Coated)
FLAX500R00B 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Precision Resistor (Conformally Coated)
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*