- 您現在的位置：買賣IC網 > PDF目錄68994 > FAN7930CM (FAIRCHILD SEMICONDUCTOR CORP) 0.5 A POWER FACTOR CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO8 PDF資料下載
參數資料
| 型號： | FAN7930CM |
| 廠商： | FAIRCHILD SEMICONDUCTOR CORP |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.5 A POWER FACTOR CONTROLLER, 350 kHz SWITCHING FREQ-MAX, PDSO8 |
| 封裝： | MS-012AA, SOP-8 |
| 文件頁數： | 5/22頁 |
| 文件大?。?/td> | 910K |
| 代理商： | FAN7930CM |
2010 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FAN7930C Rev. 1.0.0
13
FAN7930C
—
Criti
c
al
Conduc
tion
Mode
PFC
Controller
valley position of MOSFET voltage stress. For valley
detection, a minor delay by the resistor and capacitor is
needed. A capacitor increases the noise immunity at the
ZCD pin. If ZCD voltage is higher than 1.5V, an internal
ZCD comparator output becomes HIGH and LOW when
the ZCD goes below 1.4V. At the falling edge of
comparator output, internal logic turns on the MOSFET.
Figure 29.
Auxiliary Voltage Threshold
When no ZCD signal is available, the PFC controller
cannot turn on the MOSFET, so the controller checks
every switching off time and forces MOSFET turn on
when the off time is longer than 150μs. This is called the
restart timer, which triggers MOSFET turn-on at startup
and may be used at the input voltage zero-cross period.
s
150
μ
Figure 30.
Restart Timer at Startup
Because the MOSFET turn-on depends on the ZCD
input, switching frequency may increase to higher than
several megahertz due to the miss-triggering or noise
on the nearby ZCD pin. If the switching frequency is
higher than needed for critical conduction mode (CRM),
operation mode shifts to continuous conduction mode
(CCM). In CCM, unlike CRM where the boost inductor
current is reset to zero at the next switch on; inductor
current builds up at every switching cycle and can be
raised to very high current that exceeds the current
rating of the power switch or diode. This can seriously
damage the power switch and result in burn down. To
avoid this, maximum switching frequency limitation is
embedded. If ZCD signal is applied again within 3.3μs
after the previous rising edge of gate signal, this signal
is ignored internally and FAN7930C waits for another
ZCD signal. This slightly degrades the power factor
performance at light load and high input voltage.
Figure 31.
Maximum Switching Frequency
Limit Operation
5. Control: The scaled output is compared with the
internal reference voltage and sinking or sourcing
current is generated from the COMP pin by the
transconductance amplifier. The error amplifier output is
compared with the internal sawtooth waveform to give
proper turn-on time based on the controller.
Figure 32.
Control Circuit
Unlike a conventional voltage-mode PWM controller,
FAN7930C turns on the MOSFET at the falling edge of
ZCD signal. On-instance is determined by the external
signal and the turn-on time lasts until the error amplifier
output (VCOMP) and sawtooth waveform meet. When
load is heavy, output voltage decreases, scaled output
decreases, COMP voltage increases to compensate low
output, turn-on time lengthens to give more inductor
turn-on time, and increased inductor current raises the
output voltage. This is how PFC negative feedback
controller regulates output.
The maximum of VCOMP is limited to 6.5V, which dictates
the maximum turn-on time, and switching stops when
VCOMP is lower than 1.0V.
相關PDF資料 |
PDF描述 |
|---|---|
| FAN7930MX | POWER FACTOR CONTROLLER, PDSO8 |
| FAN8402DTF | BRUSHLESS DC MOTOR CONTROLLER, 1 A, PDSO20 |
| FAN8420DTF | BRUSHLESS DC MOTOR CONTROLLER, PDSO28 |
| FAN8460MP | BRUSHLESS DC MOTOR CONTROLLER, 1.2 A, DSO14 |
| FAN9611MX | 2.5 A POWER FACTOR CONTROLLER, 630 kHz SWITCHING FREQ-MAX, PDSO16 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FAN7930CMX | 功能描述:功率因數校正 IC Critical Conduction Mode PFC Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
| FAN7930CMX_G | 制造商:Fairchild Semiconductor Corporation 功能描述:IC PFC CTLR CRITICAL CONF 8-SOIC 制造商:Fairchild Semiconductor Corporation 功能描述:Power Factor Correction - PFC Critical Conduction Mode PFC Controller 制造商:Fairchild Semiconductor Corporation 功能描述:Critical Conduction Mode PFC Controller |
| FAN7930DM | 制造商:Fairchild Semiconductor Corporation 功能描述:PFC |
| FAN7930DMX | 制造商:Fairchild Semiconductor Corporation 功能描述:PFC |
| FAN7930M | 功能描述:功率因數校正 IC Critical Conduction Mode PFC Controller RoHS:否 制造商:Fairchild Semiconductor 開關頻率:300 KHz 最大功率耗散: 最大工作溫度:+ 125 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。