參數資料
型號: FAN4800CSMY
廠商: FAIRCHILD SEMICONDUCTOR CORP
元件分類: 穩壓器
英文描述: 0.5 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 268 kHz SWITCHING FREQ-MAX, PDSO16
封裝: 0.150 INCH, GREEN, MS-012AC, SOIC-16
文件頁數: 8/19頁
文件大?。?/td> 577K
代理商: FAN4800CSMY
2010 Fairchild Semiconductor Corporation
www.fairchildsemi.com
FAN4800AS/CS/01S/02S Rev. 1.0.1
16
FA
N
4800A
S/C
S
/01S/02S
PFC/PWM
Controller
Combination
PWM Control (RAMP)
When the PWM section is used in current mode, RAMP
is generally used as the sampling point for a voltage,
representing the current in the primary of the PWM’s
output transformer. The voltage is derived either from a
current-sensing resistor or a current transformer. In
voltage mode, RAMP is the input for a ramp voltage
generated by a second set of timing components
(RRAMP, CRAMP) that have a minimum value of 0V and a
peak value of approximately 6V. In voltage mode,
feedforward from the PFC output bus is an excellent
way to derive the timing ramp for the PWM stage.
Generating VDD
After turning on the FAN4800AS/CS/01S/02S at 11V,
the operating voltage can vary from 9.3V to 28V. The
threshold voltage of the VDD OVP comparator is 28V
and its hysteresis is 1V. When VDD reaches 28V, OPFC
is LOW and the PWM section is not disturbed. There
are two ways to generate VDD: use auxiliary power
supply around 15V or use bootstrap winding to self-bias
the FAN4800AS/CS/01S/02S system. The bootstrap
winding can be taped from the PFC boost choke or the
transformer of the DC-to-DC stage.
Leading/Trailing Edge Modulation
Conventional PWM techniques employ trailing-edge
modulation, in which the switch turns on right after the
trailing edge of the system clock. The error amplifier
output is then compared with the modulating ramp up.
The effective duty cycle of the trailing-edge modulation
is determined during the on-time of the switch.
In the case of leading-edge modulation, the switch is
turned off exactly at the leading edge of the system
clock. When the modulating ramp reaches the level of
the error amplifier output voltage, the switch is turned
on. The effective duty-cycle of the leading-edge
modulation is determined during off-time of the switch.
相關PDF資料
PDF描述
FAN4800CSNY 0.5 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 268 kHz SWITCHING FREQ-MAX, DIP16
FAN4802SNY 0.5 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 268 kHz SWITCHING FREQ-MAX, DIP16
FAN4803CSX-2 1 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 134 kHz SWITCHING FREQ-MAX, PDSO8
FAN4803CSX-1 1 A POWER FACTOR CONTROLLER WITH POST REGULATOR, 67 kHz SWITCHING FREQ-MAX, PDSO8
FAN5019MTCX_NL SWITCHING CONTROLLER, 4000 kHz SWITCHING FREQ-MAX, PDSO28
相關代理商/技術參數
參數描述
FAN4800CSNY 功能描述:電流型 PWM 控制器 PFC/PWM Controller Combination RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
FAN4800CUM 功能描述:電流型 PWM 控制器 PFC/PWM Controller Combination RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
FAN4800CUN 功能描述:電流型 PWM 控制器 PFC/PWM Controller Combination RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
FAN4800IM 功能描述:電流型 PWM 控制器 ANG FG PFC and PWM CONTROLLER ASMC DIE RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
FAN4800IMX 功能描述:電流型 PWM 控制器 Controller PFC - PWM Combo RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14