參數資料
型號： FAN4800ASNY
廠商： Fairchild Semiconductor
文件頁數： 15/19頁
文件大?。?/td> 860K
描述： IC CTLR COMBO PFC/PWM 16-DIP
標準包裝： 30
模式： 平均電流
頻率 - 開關： 240kHz ~ 268kHz
電流 - 啟動： 30µA
電源電壓： 11 V ~ 26 V
工作溫度： -40°C ~ 105°C
安裝類型： 通孔
封裝/外殼： 16-DIP（0.300"，7.62mm）
供應商設備封裝： 16-DIP
包裝： 管件
 
?2010 Fairchild Semiconductor Corporation
 
www.fairchildsemi.com
FAN4800AS/CS/01S/02S " Rev. 1.0.2
15
 
Two-Level PFC Function
To improve the efficiency, the system can reduce PFC
switching loss at low line and light load by reducing the
PFC output voltage. The two-level PFC output of the
FAN4801S/02S can be programmable.
As Figure 27 shows, FAN4801S/02S detect the voltage
of VEA and VRMS pins to determine if the system
operates low line and light load. At the second-level
PFC, there is a current of 20 礎 through R
F2
 from the
FBPFC pin. The second-level PFC output voltage can
be calculated as.
(
)
1   2
2
2
2.5
20
F    F
F
F
R    R
Output
V
A   R
R
?/DIV>
+
E
?/DIV>

?/DIV>
 
(3)
For example, if the second-level PFC output voltage is
expected   as   300 V   and   normal   voltage   is   387 V,
according to the equation, R
F2
 is 28 k& R
F1
 is 4.3 M&.
The programmable range of second level PFC output
voltage is 340 V ~ 300 V.
 
Figure 27.    Two-Level PFC Scheme
Oscillator (RT/CT)
The oscillator frequency is determined by the values of
R
T
  and C
T
, which determine the ramp and off-time of
the oscillator output clock:
/
/
1
RT  CT
RT  CT    DEAD
f
t
t
=
+
 
(4)
The dead time of the oscillator is derived from the
following equation:
/
1
ln
3.8
RT  CT
T
T
VREF
t
C    R
VREF

?/DIV>
?/DIV>
=
?/DIV>
?/DIV>
?/DIV>
?/DIV>

?/DIV>
?/DIV>
 
(5)
at V
REF
=7.5 V and t
RT/CT
=C
T
 x R
T
 x 0.56.
The dead time of the oscillator is determined using:
2.8
360
7.78
DEAD
T
T
V
t
C
C
mA
=
?/DIV>
=
?/DIV>
 
(6)
The dead time is so small (t
RT/CT
>>t
DEAD
) that the
operating frequency can typically be approximated by:
/
/
1
RT  CT
RT  CT
f
t
=
 
(7)
 
Pulse Width Modulator (PWM)
The operation of the PWM section is straightforward,
but there are several points that should be noted.
Foremost among these is the inherent synchronization
of PWM with the PFC section of the device, from which
it also derives its basic timing. The PWM is capable of
current-mode or voltage-mode operation. In current-
mode applications, the PWM ramp (RAMP) is usually
derived   directly   from   a   current-sensing   resistor   or
current transformer in the primary side of the output
stage. It is thereby representative of the current flowing
in the converters output stage. I
LIMIT
, which provides
cycle-by-cycle current limiting, is typically connected to
RAMP in such applications. For voltage-mode operation
and certain specialized applications, RAMP can be
connected to a separate RC timing network to generate
a voltage ramp against which FBPWM is compared.
Under these conditions, the use of voltage feedforward
from the PFC bus can assist in line regulation accuracy
and response. As in current-mode operation, the I
LIMIT
 
input is used for output stage over-current protection.
No voltage error amplifier is included in the PWM stage,
as this function is generally performed on the output
side of the PWMs isolation boundary. To facilitate the
design of opto-coupler feedback circuitry, an offset has
been built into the PWMs RAMP input that allows
FBPWM to command a 0% duty cycle for input voltages
below typical 1.5 V.
PWM Cycle-by-Cycle Current Limiter
The ILIMIT pin is a direct input to the cycle-by-cycle
current limiter for the PWM section. Should the input
voltage at this pin exceed 1 V, the output flip-flop is reset
by the clock pulse at the start of the next PWM power
cycle. When the I
LIMIT
 triggers the cycle-by-cycle bi-cycle
current, it limits the PWM duty cycle mode and the power
dissipation is reduced during the dead-short condition.
V
IN
 OK Comparator
The V
IN
  OK comparator monitors the DC output of the
PFC and inhibits the PWM if the voltage on FBPFC is
less than its nominal 2.4 V. Once the voltage reaches
2.4 V, which corresponds to the PFC output capacitor
being charged to its rated boost voltage, soft-start begins.
PWM Soft-Start (SS)
PWM startup is controlled by selection of the external
capacitor   at   soft-start.   A   current   source   of   10 礎
supplies the charging current for the capacitor and
startup of the PWM begins at 1.5 V.
相關PDF資料
PDF描述
FAN4800AUN IC PWM/PFC CTLR COMBO 16-MDIP
FAN4800CUN IC PWM/PFC CTLR COMBO 16-MDIP
FAN4802MY IC PFC CTRLR AVERAGE CURR 16SOP
FAN4802SNY IC CTLR PFC/PWM COMBO 16-PDIP
FAN6920MRMY IC PWM CTLR PFC/QUASI-RES 16SOP
相關代理商/技術參數
參數描述
FAN4800AU 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:PFC/ PWM Controller Combination
FAN4800AUM 功能描述:電流型 PWM 控制器 PFC + PWM Controller Combo RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
FAN4800AUN 功能描述:電流型 PWM 控制器 PFC + PWM Controller Combo RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
FAN4800C 制造商:FAIRCHILD 制造商全稱:Fairchild Semiconductor 功能描述:PFC/PWM Controller Combination
FAN4800CMY 功能描述:電流型 PWM 控制器 PWM/PFC, Avg Curr 30uA SU, 2.6mA Op RoHS:否 制造商:Texas Instruments 開關頻率:27 KHz 上升時間: 下降時間: 工作電源電壓:6 V to 15 V 工作電源電流:1.5 mA 輸出端數量:1 最大工作溫度:+ 105 C 安裝風格:SMD/SMT 封裝 / 箱體:TSSOP-14
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*