- 您現在的位置：買賣IC網 > PDF目錄64885 > FA7622CE 0.6 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 PDF資料下載
參數資料
| 型號： | FA7622CE |
| 元件分類： | 穩壓器 |
| 英文描述： | 0.6 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| 封裝： | SSOP-20 |
| 文件頁數： | 7/8頁 |
| 文件大小： | 67K |
| 代理商： | FA7622CE |
FA7622CP(E)
7
6. IC ON/OFF control circuit
This control circuit turns the entire IC ON or OFF by an
external signal using an ON/OFF control pin to limit the IC’s
current consumption to 10
A or less.
Figure 13 shows the IC ON/OFF control circuit and Fig. 14
shows its timing.
To turn the IC OFF, this circuit clamps OUT1 (OUT2) to
ground when the ON/OFF pin voltage is controlled to less than
0.60V. The internal bias current is cut off to turn off the
switching transistor.
To turn the IC ON, raise the ON/OFF pin voltage immediately
to 3.0V or more to charge the soft-start capacitor gradually.
7. Voltage boost circuit
By using the circuit shown in Fig. 15, this IC generates a
voltage 6.5V (typ.) higher than the VCC1 input voltage at the
VCC2 pin. This circuit allows the IC to drive MOSFET gates
directly. With this circuit, the IC can drive a low-level side
N-channel MOSFET at 3.6 to 18V as VCC1 (not possible with
conventional ICs). In addition, an N-channel MOSFET can be
used on the high-level side of a buck chopper. In Fig. 15, the
inductor (L) is about 100
H or more and the capacitor (Cup)
should be greater than about 0.1
F.
If voltage boost is not necessary, connect the VCC1 and VCC2
pins directly, and SW pin must be opened.
8. Undervoltage lock-out circuit
This circuit prevents a malfunction at a low supply voltage.
When the supply voltage VCC1 rises and reaches 3.0V, this
circuit is activated. When VCC1 drops below 2.9V, this circuit
clamps OUT1 (OUT2) to ground. The CP pin voltage is reset
to low by means of cutting off a power supply input.
9. Output circuit
As Fig. 17 shows, OUT1 and OUT2 with a totempole
structure can drive a MOSFET.
Since both the maximum output source and sink currents are
600mA, a MOSFET can be switched at high speed.
Fig. 14 Control of output
Fig. 16
ON/OFF
3.0V
0.6V
OUT1
(OUT2)
ID
Fig. 13
OUT1
(OUT2)
Time
0V
ON/OFF
3.0V
Voltage waveforms
14
13
12
VCC1
VCC2
SW
LD
CUP
R E G U L A T O R
Fig. 15
GND
OUT1
(OUT2)
VCC2
相關PDF資料 |
PDF描述 |
|---|---|
| FA7622CP | 0.6 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDIP20 |
| FA7622M | 0.6 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDSO20 |
| FA7622P | 0.6 A DUAL SWITCHING CONTROLLER, 1000 kHz SWITCHING FREQ-MAX, PDIP20 |
| FA7630CE | 0.5 A DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDSO20 |
| FA7630CP | 0.5 A DUAL SWITCHING CONTROLLER, 500 kHz SWITCHING FREQ-MAX, PDIP20 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| FA7622CP | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Switching Power Supply Control |
| FA7622CPE | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Switching Power Supply Control |
| FA7622P | 制造商:未知廠家 制造商全稱:未知廠家 功能描述: |
| FA7630CE | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
| FA7630CP | 制造商:FUJI 制造商全稱:Fuji Electric 功能描述:Bipolar IC For Switching Power Supply Control |
發布緊急采購，3分鐘左右您將得到回復。