- 您現在的位置：買賣IC網 > PDF目錄4527 > EX64-PTQG64 (Microsemi SoC)IC FPGA ANTIFUSE 3K 64-TQFP PDF資料下載
參數資料
| 型號： | EX64-PTQG64 |
| 廠商： | Microsemi SoC |
| 文件頁數： | 46/48頁 |
| 文件大小： | 0K |
| 描述： | IC FPGA ANTIFUSE 3K 64-TQFP |
| 標準包裝： | 160 |
| 系列： | EX |
| 邏輯元件/單元數： | 128 |
| 輸入/輸出數： | 41 |
| 門數： | 3000 |
| 電源電壓： | 2.3 V ~ 2.7 V |
| 安裝類型： | 表面貼裝 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 64-LQFP |
| 供應商設備封裝： | 64-TQFP（10x10） |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁當前第46頁第47頁第48頁
eX Family FPGAs
Revision 10
1-3
Routing Resources
Clusters and SuperClusters can be connected through the use of two innovative local routing resources
called FastConnect and DirectConnect, which enable extremely fast and predictable interconnection of
modules within Clusters and SuperClusters (Figure 1-4). This routing architecture also dramatically
reduces the number of antifuses required to complete a circuit, ensuring the highest possible
performance.
DirectConnect is a horizontal routing resource that provides connections from a C-cell to its neighboring
R-cell in a given SuperCluster. DirectConnect uses a hard-wired signal path requiring no programmable
interconnection to achieve its fast signal propagation time of less than 0.1 ns (–P speed grade).
FastConnect enables horizontal routing between any two logic modules within a given SuperCluster and
vertical routing with the SuperCluster immediately below it. Only one programmable connection is used
in a FastConnect path, delivering maximum pin-to-pin propagation of 0.3 ns (–P speed grade).
In addition to DirectConnect and FastConnect, the architecture makes use of two globally oriented
routing resources known as segmented routing and high-drive routing. The segmented routing structure
of Microsemi provides a variety of track lengths for extremely fast routing between SuperClusters. The
exact combination of track lengths and antifuses within each path is chosen by the fully automatic place-
and-route software to minimize signal propagation delays.
Clock Resources
eX’s high-drive routing structure provides three clock networks. The first clock, called HCLK, is hardwired
from the HCLK buffer to the clock select MUX in each R-Cell. HCLK cannot be connected to
combinational logic. This provides a fast propagation path for the clock signal, enabling the 3.9 ns clock-
to-out (pad-to-pad) performance of the eX devices. The hard-wired clock is tuned to provide a clock skew
of less than 0.1 ns worst case. If not used, the HCLK pin must be tied LOW or HIGH and must not be left
floating. Figure 1-5 describes the clock circuit used for the constant load HCLK.
HCLK does not function until the fourth clock cycle each time the device is powered up to prevent false
output levels due to any possible slow power-on-reset signal and fast start-up clock circuit. To activate
HCLK from the first cycle, the TRST pin must be reserved in the Design software and the pin must be tied
to GND on the board. (See the "TRST, I/O Boundary Scan Reset Pin" on page 1-32).
The remaining two clocks (CLKA, CLKB) are global routed clock networks that can be sourced from
external pins or from internal logic signals (via the CLKINT routed clock buffer) within the eX device.
CLKA and CLKB may be connected to sequential cells or to combinational logic. If CLKA or CLKB is
sourced from internal logic signals, the external clock pin cannot be used for any other input and must be
tied LOW or HIGH and must not float. Figure 1-6 describes the CLKA and CLKB circuit used in eX
devices.
Figure 1-4 DirectConnect and FastConnect for SuperClusters
SuperClusters
DirectConnect
No antifuses
0.1 ns routing delay
FastConnect
One antifuse
0.5 ns routing delay
Routing Segments
Typically 2 antifuses
Max. 5 antifuses
相關PDF資料 |
PDF描述 |
|---|---|
| EX128-FTQ64 | IC FPGA ANTIFUSE 6K 64-TQFP |
| ACM44DRXS | CONN EDGECARD 88POS DIP .156 SLD |
| A3P250-1QNG132I | IC FPGA 1KB FLASH 250K 132-QFN |
| A3P060-2TQG144 | IC FPGA 1KB FLASH 60K 144-TQFP |
| A3P060-2TQ144 | IC FPGA 1KB FLASH 60K 144-TQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EX64-PTQG64I | 功能描述:IC FPGA ANTIFUSE 3K 64-TQFP RoHS:是 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:EX 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
| EX64-TQ100 | 功能描述:IC FPGA ANTIFUSE 3K 100-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:EX 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
| EX64-TQ100A | 功能描述:IC FPGA ANTIFUSE 3K 100-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:EX 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
| EX64-TQ100I | 功能描述:IC FPGA ANTIFUSE 3K 100-TQFP RoHS:否 類別:集成電路 (IC) >> 嵌入式 - FPGA（現場可編程門陣列） 系列:EX 標準包裝:152 系列:IGLOO PLUS LAB/CLB數:- 邏輯元件/單元數:792 RAM 位總計:- 輸入/輸出數:120 門數:30000 電源電壓:1.14 V ~ 1.575 V 安裝類型:表面貼裝 工作溫度:-40°C ~ 85°C 封裝/外殼:289-TFBGA，CSBGA 供應商設備封裝:289-CSP（14x14） |
| EX64-TQ100PP | 制造商:ACTEL 制造商全稱:Actel Corporation 功能描述:eX Family FPGAs |
發布緊急采購，3分鐘左右您將得到回復。