- 您現在的位置：買賣IC網 > PDF目錄16860 > EVB90308 (Melexis Technologies NV)DEMO KIT MLX90308 SENS INTERFACE PDF資料下載
參數資料
| 型號： | EVB90308 |
| 廠商： | Melexis Technologies NV |
| 文件頁數： | 6/28頁 |
| 文件大?。?/td> | 0K |
| 描述： | DEMO KIT MLX90308 SENS INTERFACE |
| 標準包裝： | 1 |
| 主要目的： | 接口，傳感器至模數轉換器接口，可編程 |
| 嵌入式： | 是，MCU，8 位 |
| 已用 IC / 零件： | MLX90308 |
| 主要屬性： | 用于橋型傳感器的 MCU 控制信號調節 |
| 次要屬性： | GUI 輸出類型：絕對電壓，比率制電壓，電流輸出模式 |
| 已供物品： | 板，文檔，樣品，軟件 |
| 產品目錄頁面： | 1460 (CN2011-ZH PDF) |
| 相關產品： | MLX90308LDF-DAA-000-TU-ND - IC SENSOR PROG INTERFACE 16-SOIC |
| 其它名稱： | DK90308 DK90308-ND |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
3901090308
Rev 007
Page 14
May/12
MLX90308
Programmable Sensor Interface
Selected input
MUX Value
TPO
0010
IAO
0110
GNO
0000
VMO
0011
Level Steering
The level steering option allows configuration of the IO
pins as outputs to indicate the relative level of a
selected signal. See Figure 7. The levels at which the
two outputs change state are programmed by the
user. The programmed levels are set as eight bit
numbers and compared to the upper eight bits of the
digitized signal. This function utilizes the same
resources as the alarm function. The two functions
(level
steering
and
alarm)
can
not
be
used
simultaneously. Four bytes in the EEPROM command
this option. The first byte is used to select the input,
while the last three comprise the transition levels. The
control byte for the level steering is the same as for
the alarm. The four MSB’s hold the code for the
selected
input.
The
control
byte
has
several
possibilities as designated by the MUX settings (See
Table 8)
Communications
The MLX90308 firmware transfers a complete byte of
data into and from the memory based on a simple
command structure. The commands allow data to be
read and written to and from the EEPROM and read
from the RAM. RAM data that can be read includes
the current digitized temperature and digitized GNO.
The commands are described below. Melexis provides
setup software for programming the MLX90308.
Table 8. Level Steering Bit Definitions
Table 9. Mode Byte Bit Definition
Bit
Function
Remarks
7
1= EEPROM Checksum test active
0= EEPROM Checksum test inactive
EEPROM Checksum test. Checksum test failure will
force the output to the value programmed in bytes 40
and 41 of the EEPROM (See Table 10).
6
0 = Analog Mode
1 = Digital Mode
Digital mode must be activated when VMO and CMO
both active.
5
0 = Alarm function inactive
1 = Alarm function active
Alarm functions are like “l(fā)imiting functions”:
If defined ADC INPUT is below low alarm trigger,
then DIGMOD becomes active with alarm low
output).
If defined ADC INPUT is above high alarm trigger,
then DIGMOD becomes active with alarm high
output.
Note: Deactivated if the level steering mode is active
4
0 = IO1/IO2 are not active outputs
1 = level steering: IO1/IO2 are active
outputs
Depending on the sampled input, IO1/IO2 will be a
two bit digital output. If IO1/IO2 are not active outputs,
then they will be analog inputs.
3
0 = Turbo inactive
1 = Turbo active
2
0 = VMO inactive
1 = VMO active
1
0 = Internal temperature sensor active
1 = External temperature sensor
active
0
0 = CMO inactive
1 = CMO active
CMO has fixed digital value (EEPROM byte - see
below) if both VMO and CMO are active. To activate
this value, the digital mode must be activated.
相關PDF資料 |
PDF描述 |
|---|---|
| MLG0603S4N7S | INDUCTOR MULTILAYER 4.7NH 0201 |
| KSZ8041TL-EVAL | BOARD EVALUATION KSZ8041TL |
| EEU-FR1J180 | CAP ALUM 18UF 63V 20% RADIAL |
| MLG0603S3N6S | INDUCTOR MULTILAYER 3.6NH 0201 |
| KSZ8051MLL-EVAL | BOARD EVALUATION FOR KSZ8051MLL |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVB90314 | 功能描述:DEMO KIT MLX90314 SENS INTERFACE RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVB90316-DC | 功能描述:BOARD EVAL FOR MLX90316-DC RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:Triaxis™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| EVB90316-GO | 功能描述:BOARD EVAL FOR MLX90316-GO RoHS:否 類別:編程器，開發系統 >> 評估板 - 傳感器 系列:Triaxis™ 產品培訓模塊:Lead (SnPb) Finish for COTS Obsolescence Mitigation Program 標準包裝:1 系列:- |
| EVB90320 | 功能描述:KIT EVAL BOARD CD W/SOFTWARE RoHS:否 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:PSoC® 主要目的:電源管理，熱管理 嵌入式:- 已用 IC / 零件:- 主要屬性:- 次要屬性:- 已供物品:板，CD，電源 |
| EVB90333-DC | 制造商:Melexis Semiconductors 功能描述:BOARD EVALUATION FOR MLX90333XDC 制造商:Melexis Semiconductors 功能描述:Evaluation Board for MLX90333 Triaxis Position Sensor |
發布緊急采購，3分鐘左右您將得到回復。