- 您現在的位置：買賣IC網 > PDF目錄362803 > EVAL-ADM1022 (Analog Devices, Inc.) Evaluation Board for Microprocessor System Temperature Monitor PDF資料下載
參數資料
| 型號： | EVAL-ADM1022 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Evaluation Board for Microprocessor System Temperature Monitor |
| 中文描述： | 評估板的微機監控系統的溫度 |
| 文件頁數： | 4/14頁 |
| 文件大?。?/td> | 346K |
| 代理商： | EVAL-ADM1022 |
第1頁第2頁第3頁當前第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁
EVAL-ADM1022
–4–
REV. B
C ONNE C T OR S, SWIT C H E S A ND IND IC A T OR S
T he function of the various connectors, switches and indi-
cators on the evaluation board is explained below.
T E ST C ONNE C T OR J4
T est connector J4 allows the serial data and clock lines of
the ADM1022 and the
THERM
line to be monitored.
T he connector also allows access to the V
MON
and GPI
lines.
Alternative external diode sensors may be connected be-
tween the D1 and D2 pairs of inputs.
C E NT R ONIC S INT E R F A C E C ONNE C T OR J2
If the personal computer being used with the evaluation
board does not have a System Management Bus on the
motherboard, connection between the evaluation board
should be made via a parallel printer port, using the cable
provided. T he connections to J2 are as follows:
T ABL E 1. J2 C ONNE C T IONS
J2 Pin
ADM1022 Function
Parallel Port Function
2 Serial Clock (SCLK )
DB0
3 Serial Data In (SDA)
DB1
8 Manual Reset (MR) DB6
10 Interrupt (INT ) ACK
13 Serial Data Out (SDA) SLCT
19-30 Gnd
Gnd
SMBUS INT E R F A C E C ONNE C T OR J3
T he SMBus interface connector J3 allows the evaluation
board to be connected directly to the SMBus of a personal
computer, using the DIMM interface card provided. T o
make this connection, it may be necessary to remove one
of the DIMM memory modules on the PC motherboard,
if all DIMM sockets are occupied. T his will affect the
BIOS setup and Windows 95, and should only be at-
tempted by a competent user.
RE MOT E SE NSOR SE L E C T SWIT C HE S SW4, SW3
T wo remote sensors are provided on the evaluation board;
a 2N3904 and a 2N3906 transistor. Alternative remote
sensors may be connected between the D1 and D2 termi-
nals on the test connector J4.
T ABL E 2. RE MOT E SE NSOR SE L E C T ; SW4, SW3
SW4 Position
SW3 Position
1 2
Sensor Selected
OF F OF F
C D1/D2(connector J4)
ON -
A
2N3906 (D2)
- ON
-
2N3904 (D1)
ON ON
A
D1 and D2 selected
SE RIAL BUS AD D RE SS SE L E C T (SW2)
SW2 is used to set the two LSB’s of the ADM1022’s se-
rial bus address, A1 and A0. T he ADD pin is tri-state and
can be grounded, left unconnected or tied to V
C C
. T his
means a total of three addresses are possible. It should be
noted that the ADD pin is only read at power-up. If SW2
is changed while the ADM1022 is on, the change of ad-
dress will not be effective until the device has been pow-
ered off, and on again.
As the serial bus address is 7 bits, when storing it as an 8-
bit word it must be left or right justified, with either the
MSB or the LSB of the 8-bit word as zero. T he
ADM1022 evaluation software stores the 7-bit serial bus
address as left-justified and makes the LSB zero. T able 3
shows the three possible addresses for the ADM1022.
T ABL E 3. AD M1022 D E VIC E AD D RE SSE S
SW2 Position A1 A0
Device Address
A (Gnd)
1 0
5C (Hex)
B (NC)
0 0
58 (Hex)
C (Vcc)
0 1
5A (Hex)
V
MON
SE L E C T SWIT C H, SW1
T his switch allows the V
MON
pin to monitor either the on-
board 3.3V supply, an external 3.3V supply through con-
nector J4, or a larger external supply voltage through J4,
applied across voltage divider network R4, R5. T able 4
shows the relevant switch positions.
T ABL E 4. V
MON
SE L E C T SWIT C H, SW1
SW1 Position Voltage Source (V
mon
)
A
External 5V on J4
B
External 3.3V on J4
C
On-board 3.3V
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADM1023 | Evaluation Board for Microprocessor System Temperature Monitor |
| EVAL-ADM1026EB | Complete Thermal and System Management Controller |
| EVAL-ADM1028 | Evaluation Board for PC Temperature Monitor and Fan Control ASIC |
| EVAL-ADM1030 | Evaluation Board for ACPI Temperature Monitor and PWM Fan Controller |
| EVAL-ADM1031 | TRANS,VN2222L,FET |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADM1023 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board for Microprocessor System Temperature Monitor |
| EVAL-ADM1023EB | 功能描述:BOARD EVAL FOR ADM1023 RoHS:否 類別:編程器，開發系統 >> 過時/停產零件編號 系列:- 標準包裝:1 系列:- 傳感器類型:CMOS 成像，彩色（RGB） 傳感范圍:WVGA 接口:I²C 靈敏度:60 fps 電源電壓:5.7 V ~ 6.3 V 嵌入式:否 已供物品:成像器板 已用 IC / 零件:KAC-00401 相關產品:4H2099-ND - SENSOR IMAGE WVGA COLOR 48-PQFP4H2094-ND - SENSOR IMAGE WVGA MONO 48-PQFP |
| EVAL-ADM1024EBZ | 制造商:ON Semiconductor 功能描述:EVALUATION BOARD I.C. - Boxed Product (Development Kits) |
| EVAL-ADM1026EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Complete Thermal and System Management Controller |
| EVAL-ADM1028 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Evaluation Board for PC Temperature Monitor and Fan Control ASIC |
發布緊急采購，3分鐘左右您將得到回復。