- 您現在的位置：買賣IC網 > PDF目錄362803 > EVAL-ADF7012EB2 (Analog Devices, Inc.) Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter PDF資料下載
參數資料
| 型號： | EVAL-ADF7012EB2 |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter |
| 中文描述： | 多通道ISM頻段FSK信號/的GFSK /元件Ook /約克/ ASK發射 |
| 文件頁數： | 17/28頁 |
| 文件大?。?/td> | 772K |
| 代理商： | EVAL-ADF7012EB2 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁當前第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁
ADF7012
THEORY OF OPERATION
CHOOSING THE EXTERNAL INDUCTOR VALUE
The ADF7012 allows operation at many different frequencies by
choosing the external VCO inductor to give the correct output
on 0603 CS type inductors from Coilcraft, and are intended as guidelines in choosing the inductor because board layout and
inductor type varies between applications.
Rev. 0 | Page 17 of 28
The inductor value should be chosen so it is between the
minimum and maximum value.
MIN (meas)
MAX (meas)
MIN (eqn)
MAX (eqn)
INDUCTANCE (nH)
F
1200
1000
900
1100
700
800
500
400
600
300
0
10
5
15
20
30
25
35
0
Figure 36. Output Frequency vs. External Inductor Value
Ibias = 2.0 mA.
For frequencies between 270 MHz and 550 MHz, it is
recommended to operate the VCO at twice the desired output
frequency and use the divide-by-2 option. This ensures reliable
operation over temperature and supply.
For frequencies between 130 MHz and 270 MHz, it is
recommended to operate the VCO at four times the desired
output frequency and use the divide-by-4 option.
For frequencies below 130 MHz, it is best to use the divide-by-8
option. It is not necessary to use the VCO divider for
frequencies above 550 MHz.
ADIsimPLL is a PLL design tool which can perform the
frequency calculations for the ADF7012, and is available at
www.analog.com/pll.
CHOOSING THE CRYSTAL/PFD VALUE
The choice of crystal value is an important one. The PFD
frequency must be the same as the crystal value or an integer
division of it. The PFD determines the phase noise, spurious
levels and location, deviation frequency, and the data rate in the
case of GFSK. The following sections describe some factors that
should be considered when choosing the crystal value.
Standard Crystal Values
Standard crystal values are 3.6864 MHz, 4 MHz, 4.096 MHz,
4.9152 MHz, 7.3728 MHz, 9.8304 MHz, 10 MHz, 11.0592 MHz,
12 MHz, and 14.4792 MHz. Crystals with these values are
usually available in stock and cost less than crystals with
nonstandard values.
Reference Spurious Levels
Reference spurious levels (spurs) occur at multiples of the PFD
frequency. The reference spur closest to the carrier is usually
highest with the spur further out being attenuated by the loop
filter. The level of reference spur is lower for lower PFD
frequencies. In designs with high output power where spurious
levels are the main concern, a lower PFD frequency (<5 MHz)
may be desirable.
Beat Note Spurs
These are spurs occurring for very small or very large values in
the fractional register. These are quickly attenuated by the loop
filter. Selection of the PFD therefore determines their location,
and ensures that they have negligible effect on the transmitter
spectrum.
Phase Noise
The phase noise of a frequency synthesizer improves by 3dB for
every doubling of the PFD frequency. Because ACP is related to
the phase noise, the PFD may be increased to reduce the ACP
in the system. PFD frequencies of < 5MHz typically deliver
sufficient phase noise performance for most systems.
Deviation Frequency
The deviation frequency is adjustable in steps of
14
2
)
(
PFD
F
STEP
F
Hz
=
(10)
To get the exact deviation frequency required, ensure
F
STEP
is a
factor of the desired deviation.
TIPS ON DESIGNING THE LOOP FILTER
The loop filter design is crucial in ensuring stable operation of
the transmitter, meeting Adjacent Channel Power (ACP)
specifications, and meeting spurious requirements for the
relevant regulations. ADIsimPLL is a free tool available to aid
the design of loop filters. The user enters the desired frequency
range, the reference crystal and PFD values, and the desired
loop bandwidth. ADIsimPLL gives a good starting point for the
filter, and the filter can be further optimized based on the
criteria below.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-ADF7012EB3 | Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter |
| EVAL-ADF7012EB4 | Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter |
| EVAL-ADF7012EB5 | Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter |
| EVAL-ADG936-REB | Wideband 4 GHz, 36 dB Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, Dual SPDT |
| EVAL-ADG936EB | Wideband 4 GHz, 36 dB Isolation at 1 GHz, CMOS 1.65 V to 2.75 V, Dual SPDT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-ADF7012EB3 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter |
| EVAL-ADF7012EB4 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter |
| EVAL-ADF7012EB5 | 制造商:AD 制造商全稱:Analog Devices 功能描述:Multichannel ISM Band FSK/GFSK/OOK/GOOK/ASK Transmitter |
| EVAL-ADF7020-1DBZ4 | 功能描述:BOARD EVAL ADF7020-1 405-435MHZ RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796 |
| EVAL-ADF7020-1DBZ5 | 功能描述:BOARD EVAL ADF7020-2 ADJ FREQ RoHS:是 類別:RF/IF 和 RFID >> RF 評估和開發套件，板 系列:- 標準包裝:1 系列:- 類型:GPS 接收器 頻率:1575MHz 適用于相關產品:- 已供物品:模塊 其它名稱:SER3796 |
發布緊急采購，3分鐘左右您將得到回復。