- 您現在的位置：買賣IC網 > PDF目錄362802 > EVAL-AD7877EB (Analog Devices, Inc.) Touch Screen Controller PDF資料下載
參數資料
| 型號： | EVAL-AD7877EB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Touch Screen Controller |
| 中文描述： | 觸摸屏控制器 |
| 文件頁數： | 29/44頁 |
| 文件大?。?/td> | 1002K |
| 代理商： | EVAL-AD7877EB |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁當前第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
AD7877
WRITE TIMING
No serial interface operations can take place while CS is high.
To write to the AD7877, CS must be taken low. To write to the
device, a burst of 16 clock pulses is input to DCLK while the
write data is input to DIN. Data is clocked in on the rising edge
of DCLK. If multiple write operations are to be performed, CS
must be taken high after the end of each write operation before
another write operation can be performed by taking CS low
again.
Rev. A | Page 29 of 44
READING DATA
Data is available on the DOUT pin following the falling edge of
CS, when the device is being clocked. The MSB is clocked out
on the falling edge of CS, with subsequent data bits clocked out
on the falling edge of DCLK.
After CS is taken low and the device is clocked, the AD7877
outputs data from the register whose read address is currently
stored in Control Register 1. Once this data has been output, the
address increments automatically. CS must be taken high
between reads. When CS is taken low again, reading continues
from the register whose read address is in Control Register 1,
provided that a write operation does not change the address. If
the register read address reaches 11111b, it is then reset to zero.
This feature allows all registers to be read out in sequence
without having to explicitly write all their addresses to the
device.
Note that because data-words are 16 bits long, but the data
registers are only 12 bits long, or 8 bits in the case of GPIO
registers, the first four bits of a readback data-word are zeros, or
the first 8 bits in the case of a GPIO register.
V
DRIVE
PIN
The supply voltage to all pins associated with the serial interface
(DAV, DIN, DOUT, DCLK, CS, PENIRQ, and ALERT) is
separate from the main V
CC
supply and is connected to the
V
DRIVE
pin. This allows the AD7877 to be connected directly to
processors whose supply voltage is less than the minimum
operating voltage of the AD7877, in fact, as low as 1.7 V.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7887CB | +2.7 V to +5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead uSOIC |
| EVAL-AD7888CB | +2.7 V to +5.25 V, Micropower, 8-Channel, 125 kSPS, 12-Bit ADC in 16-Lead TSSOP |
| EVAL-AD7892-2CB | LC2MOS Single Supply, 12-Bit 600 kSPS ADC |
| EVAL-AD7892-3CB | LC2MOS Single Supply, 12-Bit 600 kSPS ADC |
| EVAL-AD7898CB | Evaluation Board for 5V, 12-Bit, Serial 220kSPS ADC in 8-Pin Package |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7877EBZ | 功能描述:BOARD EVALUATION FOR AD7877 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7879-1EBZ | 功能描述:BOARD EVALUATION FOR AD7879-1 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7879EBZ | 功能描述:BOARD EVALUATION FOR AD7879 RoHS:是 類別:編程器，開發系統 >> 評估演示板和套件 系列:- 標準包裝:1 系列:- 主要目的:電信，線路接口單元（LIU） 嵌入式:- 已用 IC / 零件:IDT82V2081 主要屬性:T1/J1/E1 LIU 次要屬性:- 已供物品:板，電源，線纜，CD 其它名稱:82EBV2081 |
| EVAL-AD7887CB | 制造商:Analog Devices 功能描述:EVAL BD FOR 2.7 V TO 5.25 V, MICROPWR, 2CH, 125 KSPS, 12-BIT - Bulk |
| EVAL-AD7887CB4 | 制造商:AD 制造商全稱:Analog Devices 功能描述:2.7 V to 5.25 V, Micropower, 2-Channel, 125 kSPS, 12-Bit ADC in 8-Lead MSOP |
發布緊急采購，3分鐘左右您將得到回復。