- 您現在的位置：買賣IC網 > PDF目錄17058 > EVAL-AD7708EBZ (Analog Devices Inc)BOARD EVAL FOR AD7708 PDF資料下載
參數資料
| 型號： | EVAL-AD7708EBZ |
| 廠商： | Analog Devices Inc |
| 文件頁數： | 26/44頁 |
| 文件大?。?/td> | 0K |
| 描述： | BOARD EVAL FOR AD7708 |
| 標準包裝： | 1 |
| ADC 的數量： | 1 |
| 位數： | 16 |
| 采樣率（每秒）： | 1.37k |
| 數據接口： | 串行 |
| 輸入范圍： | ±2.5 V |
| 在以下條件下的電源（標準）： | 3.84mW @ 3V |
| 工作溫度： | -40°C ~ 85°C |
| 已用 IC / 零件： | AD7708 |
| 已供物品： | 板，CD |
| 相關產品： | AD7708BRZ-ND - IC ADC 16BIT R-R 8/10CH 28SOIC AD7708BRUZ-REEL7-ND - IC ADC 16BIT R-R 8/10CH 28TSSOP AD7708BRZ-REEL7-ND - IC ADC 16BIT R-R 8/10CH 28SOIC AD7708BRZ-REEL-ND - IC ADC 16BIT R-R 8/10CH 28SOIC AD7708BRUZ-REEL-ND - IC ADC 16BIT R-R 8/10CH 28TSSOP AD7708BRUZ-ND - IC ADC 16BIT R-R 8/10CH 28-TSSOP AD7708BRU-REEL7-ND - IC ADC 16BIT R-R 8/10CH 28-TSSOP AD7708BRU-REEL-ND - IC ADC 16BIT R-R 8/10CH 28-TSSOP AD7708BRU-ND - IC ADC 16BIT R-R 8/10CH 28-TSSOP AD7708BR-REEL7-ND - IC ADC 16BIT R-R 8/10CH 28-SOIC 更多... |
| 其它名稱： | EVAL-AD7708EB EVAL-AD7708EB-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁當前第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁
REV. 0
–32–
AD7708/AD7718
Configuring the AD7708/AD7718
All user-accessible registers on the AD7708 and AD7718 are
accessed via the serial interface. Communication with any of
these registers is initiated by first writing to the Communica-
tions Register. Figures 16, 17, and 18 show flow diagrams for
initializing the ADC, a sequence for calibrating the ADC chan-
nels, and a routine that cycles through and reads all channels.
Figure 16 shows a flowchart detailing necessary programming
steps required to initialize the ADC. The following are the general
programming steps required:
1. Configure and initialize the microcontroller or microprocessor
serial port.
2. Initialize the AD7708/AD7718 by configuring the following
registers:
a. IOCON to configure the digital I/O port.
b. FILTER to configure the update rate for each channel.
c. ADCCON to select the active input channel, select
the analog input range, and select unipolar or bipolar
operation.
d. MODE to configure the operating mode. The mode
register selects chop or nonchop operation, buffered/
unbuffered operation of the AINCOM input, 8-/10-
channel mode of operation and reference select along
with the selection of conversion, calibration or idle
modes of operation.
All operations consist of a write to the communications register
to specify the next operation as a write to a specified register.
Data is then written to the specified register. When each sequence
is complete, the ADC defaults to waiting for another write to
the communications register to specify the next operation.
WRITE TO COMMUNICATIONS REGISTER SETTING UP
NEXT OPERATION TO BE A WRITE TO THE MODE
REGISTER. CALIBRATE AND SELECT MODE OF
OPERATION
WRITE TO COMMUNICATIONS REGISTER SETTING UP
NEXT OPERATION TO BE A WRITE TO THE ADC
CONTROL REGISTER. CONFIGURE ADCCON
WRITE TO COMMUNICATIONS REGISTER SETTING UP
NEXT OPERATION TO BE A WRITE TO THE FILTER
REGISTER. SET SF WORD FOR REQUIRED
UPDATE RATE
WRITE TO COMMUNICATIONS REGISTER SELECTING
NEXT OPERATION TO BE A WRITE TO THE IOCON
REGISTER AND CONFIGURE THIS REGISTER
POWER-ON/RESET FOR AD7708/AD7718
CONFIGURE AND INITIALIZE
C/ P SERIAL PORT
START
Figure 16. Initializing AD7708/AD7718
END
CAL
ANOTHER
CHANNEL
WRITE TO MODE REGISTER SELECTING
FULL-SCALE CALIBRATION
WRITE TO MODE REGISTER SELECTING
ZERO-SCALE CALIBRATION
WRITE TO ADCCON SELECTING CHANNEL AND CONFIGURING
INPUT RANGE AND UNIPOLAR/BIPOLAR MODE
CALIBRATION ROUTINE
MD BITS
= 001?
NO
YES
MD BITS
= 001?
NO
YES
NO
Figure 17. Calibrating the AD7708/AD7718
Figure 17 shows a flowchart detailing necessary programming
steps required when calibrating the AD7708/AD7718. The
AD7708/AD7718 have dedicated calibration register pairs for
each of the fully-differential input channels. Having a dedicated
register pair per channel allows each channel to be calibrated as
part of the initialization and the ADC picks up the relevant
coefficients for each channel during normal operation. When
operating is pseudo-differential mode channels share calibration
register pairs. Channels that share coefficients should be config-
ured with the same operating conditions to avoid having to
calibrate each time a channel is switched, especially with chop
mode disabled. The AD7708/AD7718 are factory-calibrated
with chop mode enabled and, therefore, if the ADC is operated
at the same conditions as the factory-calibration field calibra-
tions will not be required. Extremely low offset error and offset
and gain drift errors are a by product of the chopping scheme.
When operating with chop mode disabled, the user can achieve
faster throughput times. An offset calibration is required with
chop disabled when a gain or temperature change occurs. The
following are the general programming steps required when
calibrating a channel on the AD7708/AD7718.
相關PDF資料 |
PDF描述 |
|---|---|
| RPP20-4812D/N | CONV DC/DC 20W 36-75VIN +/-12V |
| EBA14DTKT-S288 | CONN EDGECARD 28POS .125 EXTEND |
| RPP20-4805S/N | CONV DC/DC 20W 36-75VIN 05VOUT |
| ECM12DRMT | CONN EDGECARD 24POS .156 WW |
| DEMO51AC256KIT | KIT DEMO DEMOAC DC9S08A |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7709EB | 制造商:Analog Devices 功能描述:EVAL KIT FOR 16BIT- ADC W/ SWITABLE CURRENT SOURCES - Bulk |
| EVAL-AD7710EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:Signal Conditioning ADC |
| EVAL-AD7711EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Signal Conditioning ADC with RTD Excitation Currents |
| EVAL-AD7712EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Signal Conditioning ADC |
| EVAL-AD7713EB | 制造商:AD 制造商全稱:Analog Devices 功能描述:LC2MOS Loop-Powered Signal Conditioning ADC |
發布緊急采購，3分鐘左右您將得到回復。