- 您現在的位置：買賣IC網 > PDF目錄362802 > EVAL-AD7671CB (Analog Devices, Inc.) Evaluation Board AD766X/AD767X PDF資料下載
參數資料
| 型號： | EVAL-AD7671CB |
| 廠商： | Analog Devices, Inc. |
| 英文描述： | Evaluation Board AD766X/AD767X |
| 中文描述： | 評估板AD766X/AD767X |
| 文件頁數： | 5/15頁 |
| 文件大?。?/td> | 1841K |
| 代理商： | EVAL-AD7671CB |
REV PrK
–5–
EVAL-AD766XCB/AD767XCB
PRELIMINARY TECHNICAL DATA
TESTING METHODS
Histogram
To perform a histogram test, apply a DC signal to the input. It
is advised to filter the signal to make the DC Source noise com-
patible with that of the ADC. C26 provides this filtering.
AC Testing
To perform an AC test, apply a sinusoidal signal to the
evaluation board. Low distortion, better than 100dB, is required
to allow true evaluation of the part. One possibility is to filter the
input signal from the AC source. There is no suggested
bandpass filter but consideration should be taken in the choice.
Furthermore, when the full-scale input range is more than a few
Vpp, it is recommended that you use the on board amplifier to
amplify the signal, thus preventing the filter from distorting the
input signal.
Please refer to Figures 8,9,10 and 11 to see the screens of the
software.
Software Description
The AD16bit.exe is the software which allows you to analyze
different performance characteristics of the AD766X,
AD767X, AD97X and AD67X 16-bit ADC family. The soft-
ware allows you to test the histogram as well as perform
different AC tests.
Setup Requirements
- Evaluation Control Board 2 (ADSP2189)
- Evaluation Board
- Power Supply (AC 15V/1A source could be bought from
ADI)
- Parallel Port Cable (provided with the evaluation control
board)
- AC Source (low distortion)
- DC Source (low noise)
- Bandpass Filter (value based on your signal frequency, low
distortion)
USE OF EVAL-AD766XCB/AD767XCB AS STAND-
ALONE EVALUATION BOARD
You have the option of using the
EVAL-AD766XCB/AD767XCB as a stand-alone evaluation
board. This method does not require the control board, nor does
it require use of the accompanied software. The digital output
will now be available on P1 (20-pin connector, for use in serial
mode) or P2 (40-pin connector, for use in parallel mode). Cer-
tain modifications have to be made on the board to allow proper
operation of the evaluation board. Refer to Table II to obtain
the jumper positions for stand-alone operation. When in stand-
alone,
could be externally applied or is generated
internally according to Table I.
Please refer to Figure 1 to obtain the data output pins on the
connectors.
Data is updated on the falling edge of BUSY.
are inputs to the FPGA and are connected to P1 and P2.
When
, CONTROL are low and
the default value defined by the on-board pull-up/pull-down
resistors, the data bus BD available on the P2 connector is
enabled.
and
is high, which is
SUPPLYING THE BOARD FOR STAND-ALONE USE
SJ1 is the analog supply. Connect VA+ to +5V and AGND to
GND. SJ2 is the digital supply. SJ2 requires the same values as
SJ1, and SJ2 may be connected to SJ1. SJ3 is the supply for the
front end amplifier (U6). Connect +12V to VS+, GND to
AGND, and -12V to VS-.
相關PDF資料 |
PDF描述 |
|---|---|
| EVAL-AD7683CB | 16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| EVAL-CONTROLBRD3 | 16-Bit, 100 kSPS PulSAR ADC in MSOP/QFN |
| EVAL-AD7705EB | 3 V/5 V, 1 mW 2-/3-Channel 16-Bit, Sigma-Delta ADCs |
| EVAL-AD7706EB | 3 V/5 V, 1 mW 2-/3-Channel 16-Bit, Sigma-Delta ADCs |
| EVAL-AD7707EB | Evaluation Board for the AD7707 3V/5V, +/-10V Input Range, 1mW, 3Channel, 16-Bit, Sigma Delta ADC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EVAL-AD7671CBZ | 功能描述:BOARD EVALUATION FOR AD7671 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7671EDZ | 功能描述:BOARD EVAL FOR AD7671 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7674CB | 功能描述:BOARD EVAL FOR AD7674 RoHS:否 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7674CBZ | 功能描述:BOARD EVALUATION FOR AD7674 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:PulSAR® 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
| EVAL-AD7674EDZ | 功能描述:BOARD EVAL FOR AD7674 RoHS:是 類別:編程器，開發系統 >> 評估板 - 模數轉換器 (ADC) 系列:* 產品培訓模塊:Obsolescence Mitigation Program 標準包裝:1 系列:- ADC 的數量:1 位數:12 采樣率（每秒）:94.4k 數據接口:USB 輸入范圍:±VREF/2 在以下條件下的電源（標準）:- 工作溫度:-40°C ~ 85°C 已用 IC / 零件:MAX11645 已供物品:板，軟件 |
發布緊急采購，3分鐘左右您將得到回復。