- 您現在的位置：買賣IC網 > PDF目錄362797 > EV0074 (Monolithic Power Systems, Inc.) Triple Output TFT Bias Converter PDF資料下載
參數資料
| 型號： | EV0074 |
| 廠商： | Monolithic Power Systems, Inc. |
| 英文描述： | Triple Output TFT Bias Converter |
| 中文描述： | 三輸出TFT偏置轉換器 |
| 文件頁數： | 5/5頁 |
| 文件大?。?/td> | 249K |
| 代理商： | EV0074 |
EV0074 (MP1530) – TRIPLE OUTPUT TFT BIAS CONVERTER
EVALUATION BOARD
NOTICE:
The information in this document is subject to change without notice. Please contact MPS for current specifications.
Users should warrant and guarantee that third party Intellectual Property rights are not infringed upon when integrating MPS
products into any application. MPS will not assume any legal responsibility for any said applications.
EV0074 (MP1530) Rev. 1.2
8/23/2005
www.MonolithicPower.com
5
MPS Proprietary Information. Unauthorized Photocopy and Duplication Prohibited.
2005 All Rights Reserved.
TM
QUICK START GUIDE
The three output voltages of this board are set to +13V, +27V, and –8.5V. The board layout
accommodates most commonly used inductors and output capacitors.
1. Attach the positive end of loads to the VMAIN, VGH and GND (for the negative output) pins,
respectively. Attach negative ends of the loads to GND and VGL (for the negative output) pins.
2. Attach an input voltage 2.7V
≤
V
IN
≤
5.5V and input ground to the VIN and GND pins,
respectively.
3. The demo board starts up automatically once V
IN
is applied due to the pull-up resistor R1. To
disable the MP1530 connect the EN pin to ground.
4. During startup
RDY
will be left HIGH. Once the turn-on sequence is complete, this pin will be
pulled LOW if all regulators exceed 80% of their specified voltages. After all regulators are
turned-on, a fault in any regulator will cause
RDY
to go HIGH after approximately 15
μ
s. If the
fault persists for more than approximately 6ms (for CT=10nF), the entire chip will shut down.
5. To adjust the output voltages:
Use a 10k
to 50k
for the low-side resistor of each voltage divider (i.e. R7, R9 and R5).
V
FB1
= V
FB3
= V
REF
= 1.25V.
For the step-up converter, determine the high-side resistor R6 using the equation:
=
V
1
FB
7
R
V
V
6
R
1
FB
MAIN
Where V
MAIN
is the output voltage of the step-up converter.
For the positive charge-pump, determine the high-side resistor R8 by the equation:
=
V
3
FB
9
R
V
V
8
R
3
FB
GH
Where V
GH
is the output voltage of the positive linear regulator. Determine the number of
positive charge pump stages (N
POS
) by:
V
V
V
N
D
MAIN
V
MAIN
DROPOUT
GH
POS
V
2
+
=
Use V
DROPOUT
= 1V and V
D
= 0.4V for Schottky diodes.
For the negative charge-pump, determine the high-side resistor R4 by the equation:
=
V
REF
5
R
V
4
R
GL
Where V
GL
is the output voltage of the negative linear regulator. Determine the number of
negative charge pump stages (N
NEG
) by:
V
V
N
D
MAIN
V
DROPOUT
V
2
GL
NEG
+
=
6. Use V
DROPOUT
= 0.3V and V
D
= 0.4V for Schottky diodes.
相關PDF資料 |
PDF描述 |
|---|---|
| EV0077 | 1.3MHz Low Power Boost Converter |
| EV1517DR-00A | 3A, 25V, 1.1MHz Step-Up Converter |
| EV1517DR-00B | 3.3V, 1A Sepic Evaluation Board |
| EV1518DG-00A | Fixed Frequency WLED Driver Evaluation Board |
| EV1528DQ-00A | 9 Lamp, 20mA Preciscion WLED Driver Evaluation Board |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EV0077 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1.3MHz Low Power Boost Converter |
| EV0100 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:SINGLE TONE SIREN/ALARM SOUND GENERATOR |
| EV0171 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EvKit for CMX017 |
| EV0181 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:EvKit for CMX018 |
| EV05D130K | 制造商:World Products 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。