- 您現在的位置：買賣IC網 > PDF目錄362797 > EV0035 (Monolithic Power Systems, Inc.) Precision 6-Lamp White LED Driver PDF資料下載
參數資料
| 型號： | EV0035 |
| 廠商： | Monolithic Power Systems, Inc. |
| 英文描述： | Precision 6-Lamp White LED Driver |
| 中文描述： | 精密6燈白光LED驅動器 |
| 文件頁數： | 5/7頁 |
| 文件大?。?/td> | 145K |
| 代理商： | EV0035 |
MP1523 – PRECISION 6-LAMP WHITE LED DRIVER
INITIAL RELEASE
07/04, Rev. 1.6
www.MonolithicPower.com
5
APPLICATIONS INFORMATION
Setting the LED current
The LED current is set by the sense resistor
(R2) at FB. The LED current can be calculated
as:
2
R
V
I
FB
LED
=
Where V
FB
is 400mV. The LED current is set to
20mA if R2 = 20
.
Capacitor Selection
A 1μF to 10μF ceramic input capacitor (C1) and
a 0.47μF to 1μF ceramic output capacitor (C2)
are recommended for most applications. A
capacitor (typically 1nF) in parallel with the LED
string improves stability, input and output ripple
especially when large inductance values (10μH
or above) are used. For best stability over a
wide temperature range, use capacitors with an
X5R or X7R dielectric.
Inductor selection
The MP1523 has a 450mA inductor current limit
and can drive up to 6 LEDs at 20mA.
Inductance values (L1) from 4.7μH to 47μH
work satisfactorily. Larger values provide the
best efficiency while small inductor values allow
the smallest inductor size. To prevent
saturation, use an inductor with a saturation
current rating that matches the device current
limit.
Diode selection
The
MP1523’s
demands a high-speed rectifier (D1) for
optimum efficiency. A schottky diode is
recommended due to its fast recovery time and
low forward voltage drop. Ensure the diode’s
average and peak current ratings exceed the
average output current and peak inductor
current. In addition, the diode’s reverse
breakdown voltage must exceed the output
voltage.
high
switching
frequency
Layout
Careful PC board layout is required due to fast-
switching. All components must be placed as
close to the IC as possible. Keep the path
between inductor L1, diode D1, and output
capacitor C2 extremely short for minimal noise
and ringing. The feedback components such as
sense resistor R2 must be kept close to the FB
pin to prevent noise injection on the FB pin
trace. The ground return of C1 and C2 should
be tied close to the GND pin. See the MP1523
demo board layout for reference.
相關PDF資料 |
PDF描述 |
|---|---|
| EV0037 | Cold Cathode Fluorescent Lamp Driver |
| EV0041 | High Current Integrated Half Bridge + Driver |
| EV0042 | 1x, 1.5x, 2x High Efficiency Charge Pump 4 White LED Driver Evaluation Board |
| EV0043 | 3A, 25V, 1.1MHz Step-Up Converter |
| EV0045 | 5W - 30W Class D Mono Bridged Audio Amplifier |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EV0037 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:Cold Cathode Fluorescent Lamp Driver |
| EV0041 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:High Current Integrated Half Bridge + Driver |
| EV0042 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:1x, 1.5x, 2x High Efficiency Charge Pump 4 White LED Driver |
| EV0043 | 制造商:MPS 制造商全稱:Monolithic Power Systems 功能描述:3A, 25V, 1.1MHz Step-Up Converter |
| EV0045 | 制造商:Monolithic Power Systems 功能描述:STEREO EVALUATION BOARD - Bulk |
發布緊急采購，3分鐘左右您將得到回復。