- 您現在的位置：買賣IC網 > PDF目錄362743 > EPC1 (Electronic Theatre Controls, Inc.) Configuration Devices for SRAM-Based LUT Devices PDF資料下載
參數資料
| 型號： | EPC1 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Configuration Devices for SRAM-Based LUT Devices |
| 中文描述： | 配置SRAM器件基于LUT的器件 |
| 文件頁數： | 22/28頁 |
| 文件大?。?/td> | 380K |
| 代理商： | EPC1 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁當前第22頁第23頁第24頁第25頁第26頁第27頁第28頁
22
Altera Corporation
Configuration Devices for ACEX, APEX, FLEX & Mercury Devices Data Sheet
f
Application Note 39 (IEEE 1149.1 (JTAG) Figure9
shows the timing requirements for the JTAG signals.
BYPASS
Places the 1-bit bypass register between the
TDI
and
TDO
pins, which allows the BST
data to pass synchronously through a selected device to adjacent devices during
normal device operation.
Selects the device IDCODE register and places it between
TDI
and
TDO
, allowing the
device IDCODE to be serially shifted out of
TDO
. The device IDCODE for the EPC2 is
shown below:
0000 0001000000000010 00001101110 1
Selects the USERCODE register and places it between
TDI
and
TDO
, allowing the
USERCODE to be serially shifted out of
TDO
. The 32-bit USERCODE is a
programmable user-defined pattern.
These instructions are used when programming an EPC2 device via JTAG ports with
a MasterBlaster, ByteBlaster MV, ByteBlaster, or BitBlaster download cable, or using
a Jam STAPL File (
.jam
), Jam STAPL Byte-Code File (
.jbc
), or SVF File via an
embedded processor.
This function allows the user to initiate the APEX or FLEX configuration process by
tying
nINIT_CONF
to the APEX or FLEX device(s)
nCONFIG
pin(s). After this
instruction is updated, the
nINIT_CONF
pin is driven low. When the Initiate
Configuration instruction is cleared,
nINIT_CONF
is released, which starts the APEX
or FLEX device configuration. This instruction is used by the MAX+PLUS II software,
Jam STAPL Files, and JBC Files.
IDCODE
USERCODE
ISP Instructions
INIT_CONF
Table 8. EPC2 JTAG Instructions
JTAG Instruction
Description
相關PDF資料 |
PDF描述 |
|---|---|
| EPC1064 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1064V | Configuration Devices for SRAM-Based LUT Devices |
| EPC1213 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1441 | Configuration Devices for SRAM-Based LUT Devices |
| EPC1064 | Configuration Devices for ACEX, APEX, FLEX & Mercury Devices |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC10 | 制造商:YUXIANG 制造商全稱:YUXIANG 功能描述:EPC CORES |
| EPC-10 | 制造商:Curtis Industries 功能描述:Conn Barrier Strip 10 POS 9.52mm Solder ST Thru-Hole 15A |
| EPC100 | 制造商:EPC 制造商全稱:EPC 功能描述:Light-Curtain Device with 2-Wire Bus Interface |
| EPC1000P | 制造商:PCA 制造商全稱:PCA ELECTRONICS INC. 功能描述:Ethernet DC/DC Converter |
| EPC1000PA1 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Analog IC |
發布緊急采購，3分鐘左右您將得到回復。