- 您現在的位置：買賣IC網 > PDF目錄1920 > EPC16UC88AA (Altera)IC CONFIG DEVICE 16MBIT 88-UBGA PDF資料下載
參數資料
| 型號： | EPC16UC88AA |
| 廠商： | Altera |
| 文件頁數： | 19/36頁 |
| 文件大小： | 0K |
| 描述： | IC CONFIG DEVICE 16MBIT 88-UBGA |
| 標準包裝： | 80 |
| 系列： | EPC |
| 可編程類型： | 系統內可編程 |
| 存儲容量： | 16Mb |
| 電源電壓： | 3 V ~ 3.6 V |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 88-LFBGA |
| 供應商設備封裝： | 88-UBGA（11x8） |
| 包裝： | 托盤 |
| 其它名稱： | 544-1373 EPC16UC88AA-ND |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁當前第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁
Page 26
Power Sequencing
Enhanced Configuration (EPC) Devices Datasheet
January 2012
Altera Corporation
Power Sequencing
Altera requires that you power-up the FPGA's VCCINT supply before the EPC device's
POR expires.
Power up needs to be controlled so that the EPC device’s OE signal goes high after the
CONF
_DONE signal is pulled low. If the EPC device exits POR before the FPGA is
powered up, the CONF_DONE signal will be high because the pull-up resistor is holding
this signal high. When the EPC device exits POR, OE is released and pulled high by a
pull-up resistor. Since the EPC device samples the nCS signal on the rising edge of OE,
it detects a high level on CONF_DONE and enters an idle mode. DATA and DCLK outputs
will not toggle in this state and configuration will not begin. The EPC device will only
exit this mode if it is powered down and then powered up correctly.
1 To ensure the EPC device enters configuration mode properly, you must ensure that
the FPGA completes power-up before the EPC device exits POR.
The pin-selectable POR time feature is useful for ensuring this power-up sequence.
The EPC device has two POR settings—2 ms when PORSEL is set to a high level and
100 ms when PORSEL is set to a low level. For more margin, the 100-ms setting can be
selected to allow the FPGA to power-up before configuration is attempted.
Alternatively, a power-monitoring circuit or a power-good signal can be used to keep
the FPGA’s nCONFIG pin asserted low until both supplies have stabilized. This ensures
the correct power up sequence for successful configuration.
Programming and Configuration File Support
The Quartus II software provides programming support for the EPC device and
automatically generates the .pof for the EPC4, EPC8, and EPC16 devices. In a
multi-device project, the Quartus II software can combine the .sof for multiple
ACEX 1K, APEX 20K, APEX II, Cyclone series, FLEX 10K, Mercury, and Stratix series
FPGAs into one programming file for the EPC device.
f For more information about generating programming files, refer to the Altera
EPC devices can be programmed in-system through the industry-standard 4-pin
JTAG interface. The ISP feature in the EPC device provides ease in prototyping and
updating FPGA functionality.
After programming an EPC device in-system, FPGA configuration can be initiated by
including the EPC device’s JTAG INIT_CONF instruction (refer to Table 11).
相關PDF資料 |
PDF描述 |
|---|---|
| EPCS16SI16N | IC CONFIG DEVICE 16MBIT 16-SOIC |
| EPF10K10AQI208-3 | IC FLEX 10KA FPGA 10K 208-PQFP |
| EPF10K200EBC600-1 | IC FLEX 10KE FPGA 200K 600-BGA |
| EPF6024AQI208-3 | IC FLEX 6000 FPGA 24K 208-PQFP |
| EPF81500AQC240-2 | IC FLEX 8000A FPGA 16K 240-PQFP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EPC16UC88N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16UI88AA | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16UI88N | 功能描述:FPGA-配置存儲器 IC - Ser. Config Mem Flash 16Mb 33 MHz RoHS:否 制造商:Altera Corporation 存儲類型:Flash 存儲容量:1.6 Mbit 工作頻率:10 MHz 電源電壓-最大:5.25 V 電源電壓-最小:3 V 電源電流:50 uA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:PLCC-20 |
| EPC16XXX | 制造商:ALTERA 制造商全稱:Altera Corporation 功能描述:2. Enhanced Configuration Devices (EPC4, EPC8 & EPC16) Data Sheet |
| EPC17 | 制造商:TDK 制造商全稱:TDK Electronics 功能描述:Ferrite Cores For Power Supply and Signal Transformer EPC Cores |
發布緊急采購，3分鐘左右您將得到回復。