參數資料
型號： ENC424J600T-I/ML
廠商： Microchip Technology
文件頁數： 47/168頁
文件大小： 0K
描述： IC ETHERNET CTRLR W/SPI 44-QFN
視頻文件： Fast 100 Mbps Ethernet PICtail Plus Overview
標準包裝： 1,600
控制器類型： 以太網控制器（IEEE 802.3）
接口： SPI
電源電壓： 3 V ~ 3.6 V
電流 - 電源： 96mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 44-VQFN 裸露焊盤
供應商設備封裝： 44-QFN（8x8）
包裝： 帶卷 (TR)
配用： AC164132-ND - BOARD DAUGHTER PICTAIL ETHERNET
PIC18F2220/2320/4220/4320
DS39599G-page 138
2007 Microchip Technology Inc.
15.5
PWM Mode
In Pulse Width Modulation (PWM) mode, the CCP1 pin
produces up to a 10-bit resolution PWM output. Since
the CCP1 pin is multiplexed with the PORTC data latch,
the TRISC<2> bit must be cleared to make the CCP1
pin an output.
Figure 15-3 shows a simplified block diagram of the
CCP module in PWM mode.
For a step-by-step procedure on how to set up the CCP
module for PWM operation, see Section 15.5.3
FIGURE 15-3:
SIMPLIFIED PWM BLOCK
DIAGRAM
A PWM output (Figure 15-4) has a time base (period)
and a time that the output is high (duty cycle). The
frequency of the PWM is the inverse of the period
(1/period).
FIGURE 15-4:
PWM OUTPUT
15.5.1
PWM PERIOD
The PWM period is specified by writing to the PR2
register. The PWM period can be calculated using the
following equation.
EQUATION 15-1:
PWM frequency is defined as 1/[PWM period]. When
TMR2 is equal to PR2, the following three events occur
on the next increment cycle:
TMR2 is cleared
The CCP1 pin is set (if PWM duty cycle = 0%, the
CCP1 pin will not be set)
The PWM duty cycle is copied from CCPR1L into
CCPR1H
15.5.2
PWM DUTY CYCLE
The PWM duty cycle is specified by writing to the
CCPR1L register and to the CCP1CON<5:4> bits. Up
to 10-bit resolution is available. The CCPR1L contains
the eight MSbs and the CCP1CON<5:4> contains the
two LSbs. This 10-bit value is represented by
CCPR1L:CCP1CON<5:4>. The PWM duty cycle is
calculated by the following equation.
EQUATION 15-2:
CCPR1L and CCP1CON<5:4> can be written to at any
time but the duty cycle value is not copied into
CCPR1H until a match between PR2 and TMR2 occurs
(i.e., the period is complete). In PWM mode, CCPR1H
is a read-only register.
Note:
Clearing the CCP1CON register will force
the CCP1 PWM output latch to the default
low level. This is not the PORTC I/O data
latch.
CCPR1L
CCPR1H (Slave)
Comparator
TMR2
Comparator
PR2
(Note 1)
R
Q
S
Duty Cycle Registers
CCP1CON<5:4>
Clear Timer,
CCP1 pin and
latch D.C.
TRISC<2>
RC2/CCP1/P1A
Note: 8-bit timer is concatenated with 2-bit internal Q clock or
2 bits of the prescaler to create 10-bit time base.
Period
Duty Cycle
TMR2 = PR2
TMR2 = Duty Cycle
TMR2 = PR2
Note:
The Timer2 postscaler (see Section 13.0
“Timer2 Module”) is not used in the
determination of the PWM frequency. The
postscaler could be used to have a servo
update rate at a different frequency than
the PWM output.
PWM Period = [(PR2) + 1] 4 TOSC
(TMR2 Prescale Value)
PWM Duty Cycle = (CCPR1L:CCP1CON<5:4>)
TOSC (TMR2 Prescale Value)
相關PDF資料
PDF描述
PIC16F677-E/P IC PIC MCU FLASH 2KX14 20DIP
MCP2155-I/P IC IRDA PROTOCOL CTRLR 18DIP
MCP2150T-I/SS IC IRDA STD CONTROLLER 20SSOP
MCP2155T-I/SO IC IRDA PROTOCOL CONTRLR 18-SOIC
PIC18F25J10T-I/SS IC PIC MCU FLASH 16KX16 28SSOP
相關代理商/技術參數
參數描述
ENC424J600T-IPT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC431D05A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ENC431D-05A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STD MOV
ENC431D07A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:
ENC431D-07A 制造商:未知廠家 制造商全稱:未知廠家 功能描述:STD MOV
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*