參數資料
型號： ENC424J600-I/ML
廠商： Microchip Technology
文件頁數： 71/168頁
文件大?。?/td> 0K
描述： IC ETHERNET CTRLR W/SPI 44-QFN
視頻文件： Fast 100 Mbps Ethernet PICtail Plus Overview
標準包裝： 45
控制器類型： 以太網控制器（IEEE 802.3）
接口： SPI
電源電壓： 3 V ~ 3.6 V
電流 - 電源： 96mA
工作溫度： -40°C ~ 85°C
安裝類型： 表面貼裝
封裝/外殼： 44-VQFN 裸露焊盤
供應商設備封裝： 44-QFN（8x8）
包裝： 管件
產品目錄頁面： 684 (CN2011-ZH PDF)
配用： AC164132-ND - BOARD DAUGHTER PICTAIL ETHERNET
PIC18F2220/2320/4220/4320
DS39599G-page 160
2007 Microchip Technology Inc.
17.3.5
MASTER MODE
The master can initiate the data transfer at any time
because it controls the SCK. The master determines
when the slave (Processor 2, Figure 17-2) is to
broadcast data by the software protocol.
In Master mode, the data is transmitted/received as
soon as the SSPBUF register is written to. If the SPI is
only going to receive, the SDO output could be dis-
abled (programmed as an input). The SSPSR register
will continue to shift in the signal present on the SDI pin
at the programmed clock rate. As each byte is
received, it will be loaded into the SSPBUF register as
if a normal received byte (interrupts and status bits
appropriately set). This could be useful in receiver
applications as a “Line Activity Monitor” mode.
The clock polarity is selected by appropriately program-
ming the CKP bit (SSPCON1<4>). This then, would
give waveforms for SPI communication, as shown in
MSB is transmitted first. In Master mode, the SPI clock
rate (bit rate) is user-programmable to be one of the
following:
FOSC/4 (or TCY)
FOSC/16 (or 4 TCY)
FOSC/64 (or 16 TCY)
(Timer2 output)/2
The maximum data rate is approximately 3.0 Mbps,
limited by timing requirements (see Table 26-14
through Table 26-17).
Figure 17-3 shows the waveforms for Master mode.
When the CKE bit is set, the SDO data is valid before
there is a clock edge on SCK. The change of the input
sample is shown based on the state of the SMP bit. The
time when the SSPBUF is loaded with the received
data is shown.
FIGURE 17-3:
SPI MODE WAVEFORM (MASTER MODE)
SCK
(CKP = 0
SCK
(CKP = 1
SCK
(CKP = 0
SCK
(CKP = 1
4 Clock
Modes
Input
Sample
Input
Sample
SDI
bit 7
bit 0
SDO
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
bit 7
bit 0
SDI
SSPIF
(SMP = 1)
(SMP = 0)
(SMP = 1)
CKE = 1)
CKE = 0)
CKE = 1)
CKE = 0)
(SMP = 0)
Write to
SSPBUF
SSPSR to
SSPBUF
SDO
bit 7
bit 6
bit 5
bit 4
bit 3
bit 2
bit 1
bit 0
(CKE = 0)
(CKE = 1)
Next Q4 Cycle
after Q2
↓
相關PDF資料
PDF描述
MCP2510-E/SO IC CAN CTLR EXTENDED TEMP 18SOIC
PIC12C508AT-04E/SM IC MCU OTP 512X12 8-SOIJ
D38999/20MJ20HN CONN RCPT 30POS WALL MNT W/PINS
V72A3V3C264B3 CONVERTER MOD DC/DC 3.3V 264W
D38999/26JG75PN CONN PLUG 4POS STRAIGHT W/PINS
相關代理商/技術參數
參數描述
ENC424J600-IPT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC424J600T-I/ML 功能描述:以太網 IC 10/100 Base-T Stand alone Ethernet Ctrlr RoHS:否 制造商:Micrel 產品:Ethernet Switches 收發器數量:2 數據速率:10 Mb/s, 100 Mb/s 電源電壓-最大:1.25 V, 3.45 V 電源電壓-最小:1.15 V, 3.15 V 最大工作溫度:+ 85 C 封裝 / 箱體:QFN-64 封裝:Tray
ENC424J600T-I/PT 功能描述:外圍驅動器與原件 - PCI 10/100 Base-T Stand alone Ethernet Ctrlr RoHS:否 制造商:PLX Technology 工作電源電壓: 最大工作溫度: 安裝風格:SMD/SMT 封裝 / 箱體:FCBGA-1156 封裝:Tray
ENC424J600T-IML 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
ENC424J600T-IPT 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:Stand-Alone 10/100 Ethernet Controller with SPI or Parallel Interface
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*