- 您現在的位置：買賣IC網 > PDF目錄362702 > EN29LV400AT-55RTI (Electronic Theatre Controls, Inc.) Replaced by PTH04070W : PDF資料下載
參數資料
| 型號： | EN29LV400AT-55RTI |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | Replaced by PTH04070W : |
| 中文描述： | 4兆位（為512k × 8位/ 256 × 16位）閃存引導扇區閃存，CMOS 3.0伏，只 |
| 文件頁數： | 9/41頁 |
| 文件大?。?/td> | 771K |
| 代理商： | EN29LV400AT-55RTI |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁當前第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
To access the autoselect codes in-system; the host system can issue the autoselect command via
the command register, as shown in the Command Definitions table. This method does not require
V
ID
. See “Command Definitions” for details on using the autoselect mode.
Write Mode
Write operations, including programming data and erasing sectors of memory, require the host
system to write a command or command sequence to the device. Write cycles are initiated by
placing the byte or word address on the device’s address inputs while the data to be written is input
on DQ[7:0] in Byte Mode (BYTE# = L) or on DQ[15:0] in Word Mode (BYTE# = H). The host system
must drive the CE# and WE# pins Low and the OE# pin high for a valid write operation to take place.
All addresses are latched on the falling edge of WE# and CE#, whichever happens later. All data is
latched on the rising edge of WE# or CE#, whichever happens first. The system is not required to
provide further controls or timings. The device automatically provides internally generated program /
erase pulses and verifies the programmed /erased cells’ margin. The host system can detect
completion of a program or erase operation by observing the RY/BY# pin, or by reading the DQ[7]
(Data# Polling) and DQ[6] (Toggle) status bits.
The ‘Command Definitions’ section of this document provides details on the specific device
commands implemented in the EN29LV400A.
Sector Protection/Unprotection
The hardware sector protection feature disables both program and erase operations in any sector. The
hardware sector unprotection feature re-enables both program and erase operations in previously
protected sectors.
There are two methods to enabling this hardware protection circuitry. The first one requires only
that the RESET# pin be at V
ID
and then standard microprocessor timings can be used to enable or
disable this feature. See Flowchart 7a and 7b for the algorithm and Figure 12 for the timings.
When doing Sector Unprotect, all the other sectors should be protected first.
The second method is meant for programming equipment. This method requires V
ID
be applied to
both OE# and A9 pin and non-standard microprocessor timings are used. This method is described
in a separate document called EN29LV400A Supplement,
which can be obtained by contacting a
representative of Eon Silicon Devices, Inc.
Temporary Sector Unprotect
This feature allows temporary unprotection of previously protected
sector groups to change data while in-system. The Sector
Unprotect mode is activated by setting the RESET# pin to V
ID
.
During this mode, formerly protected sectors can be programmed
or erased by simply selecting the sector addresses. Once is
removed from the RESET# pin, all the previously protected sectors
are protected again. See accompanying figure and timing
diagrams for more details.
Notes:
1. All protected sectors unprotected.
2. Previously protected sectors protected
again.
This Data Sheet may be revised by subsequent versions 2005 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. A, Issue Date: 2005/01/07
EN29LV400A
Start
Reset#=V
ID
(note 1)
Perform Erase or Program
Operations
Reset#=V
IH
Temporary Sector
Unprotect Completed
(note 2)
相關PDF資料 |
PDF描述 |
|---|---|
| EN29LV400AT-70TC | Replaced by PTH04070W : |
| EN29LV400AT-70TCP | Replaced by PTH04070W : |
| EN29LV400AT-70TI | Replaced by PTH04070W : |
| EN29LV400AT-70TIP | Replaced by PTH04070W : |
| EN29LV400AT-90BC | Replaced by PTH04070W : |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EN29LV400AT-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:4 Mb PAR NOR 512Kx8bit/256Kx16bit 3V 48-TSOP |
| EN29LV800AB-70TC | 制造商:Eon Silicon Solution Inc 功能描述: |
| EN29LV800BB-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29LV800B Series, 8 Mbit 70 NS 48 TSOP 3 V Bottom Boot Sector NOR Flash |
| EN29LV800CT-70TIP | 制造商:EON SILICON SOLUTION INC 功能描述:8mb TSOP 70ns nor flash |
| EN29SL400B-90BIP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29SL400 Series, 4 Mbit 90 NS 48 FBGA 1.8 V Bottom Boot Sector NOR Flash |
發布緊急采購，3分鐘左右您將得到回復。