- 您現在的位置：買賣IC網 > PDF目錄362702 > EN29LV400AB-70BC (Electronic Theatre Controls, Inc.) 4 Megabit (512K X 8-bit / 256K X 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only PDF資料下載
參數資料
| 型號： | EN29LV400AB-70BC |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | 4 Megabit (512K X 8-bit / 256K X 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only |
| 中文描述： | 4兆位（為512k × 8位/ 256 × 16位）閃存引導扇區閃存，CMOS 3.0伏，只 |
| 文件頁數： | 12/41頁 |
| 文件大?。?/td> | 771K |
| 代理商： | EN29LV400AB-70BC |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁當前第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁
operation in the Erase Suspend mode, the system may once again read array data with the same
exception.
The Reset command must be issued to re-enable the device for reading array data if DQ5 goes high,
or while in the autoselect mode. See next section for details on Reset.
Reset Command
Writing the reset command to the device resets the device to reading array data. Address bits are
don’t-care for this command.
The reset command may be written between the sequence cycles in an erase command sequence
before erasing begins. This resets the device to reading array data. Once erasure begins, however,
the device ignores reset commands until the operation is complete. The reset command may be
written between the sequence cycles in a program command sequence before programming begins.
This resets the device to reading array data (also applies to programming in Erase Suspend mode).
Once programming begins, however, the device ignores reset commands until the operation is
complete.
The reset command may be written between the sequence cycles in an autoselect command
sequence. Once in the autoselect mode, the reset command must be written to return to reading
array data (also applies to autoselect during Erase Suspend).
If DQ5 goes high during a program or erase operation, writing the reset command returns the device
to reading array data (also applies during Erase Suspend).
Autoselect Command Sequence
The autoselect command sequence allows the host system to access the manufacturer and devices
codes, and determine whether or not a sector is protected. The Command Definitions table shows
the address and data requirements. This is an alternative to the method that requires V
ID
on
address bit A9 and is intended for PROM programmers.
Two unlock cycles followed by the autoselect command initiate the autoselect command sequence.
Autoselect mode is then entered and the system may read at addresses shown in Table 4 any
number of times, without needing another command sequence.
The system must write the reset command to exit the autoselect mode and return to reading array
data.
Word / Byte Programming Command
The device may be programmed by byte or by word, depending on the state of the Byte# Pin.
Programming the EN29LV400A is performed by using a four bus-cycle operation (two unlock write
cycles followed by the Program Setup command and Program Data Write cycle). When the program
command is executed, no additional CPU controls or timings are necessary. An internal timer
terminates the program operation automatically. Address is latched on the falling edge of CE# or
WE#, whichever is last; data is latched on the rising edge of CE# or WE#, whichever is first.
Programming status may be checked by sampling data on DQ7 (DATA# polling) or on DQ6 (toggle
bit). ). When the program operation is successfully completed, the device returns to read mode and
the user can read the data programmed to the device at that address. Note that data can not be
programmed from a 0 to a 1. Only an erase operation can change a data from 0 to 1. When
programming time limit is exceeded, DQ5 will produce a logical “1” and a Reset command can
return the device to Read mode.
This Data Sheet may be revised by subsequent versions 2005 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. A, Issue Date: 2005/01/07
EN29LV400A
相關PDF資料 |
PDF描述 |
|---|---|
| EN29LV400AB-70BCP | 4 Megabit (512K X 8-bit / 256K X 16-bit) Flash Memory Boot Sector Flash Memory, CMOS 3.0 Volt-only |
| EN29LV400AT-55RTCP | Replaced by PTH04070W : |
| EN29LV400AT-55RTI | Replaced by PTH04070W : |
| EN29LV400AT-70TC | Replaced by PTH04070W : |
| EN29LV400AT-70TCP | Replaced by PTH04070W : |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EN29LV400AB-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29LV400A Series, 4 Mbit (512 K x 8) 70 NS 48 TSOP 3 V Bottom Boot NOR Flash |
| EN29LV400AB-70TIP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29LV400A Series 4 Mbit (512 K x 8) 70 NS 48 TSOP 3 V Bottom Boot NOR Flash |
| EN29LV400AT-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:4 Mb PAR NOR 512Kx8bit/256Kx16bit 3V 48-TSOP |
| EN29LV800AB-70TC | 制造商:Eon Silicon Solution Inc 功能描述: |
| EN29LV800BB-70TCP | 制造商:EON SILICON SOLUTION INC 功能描述:EN29LV800B Series, 8 Mbit 70 NS 48 TSOP 3 V Bottom Boot Sector NOR Flash |
發布緊急采購，3分鐘左右您將得到回復。