參數資料
型號： EN25P80-50HI
廠商： Eon Silicon Solution Inc.
元件分類： FLASH
英文描述： 4 Mbit Uniform Sector, Serial Flash Memory
中文描述： 4兆位統一部門，串行閃存
文件頁數： 13/30頁
文件大?。?/td> 396K
代理商： EN25P80-50HI
This Data Sheet may be revised by subsequent versions 2004 Eon Silicon Solution, Inc., www.essi.com.tw
or modifications due to changes in technical specifications.
Rev. C, Issue Date: 2006/12/25
EN25P80
Page Program (PP) (02h)
The Page Program (PP) instruction allows bytes to be programmed in the memory. Before it can be
accepted, a Write Enable (WREN) instruction must previously have been executed. After the Write Enable
(WREN) instruction has been decoded, the device sets the Write Enable Latch (WEL).
The Page Program (PP) instruction is entered by driving Chip Select (CS#) Low, followed by the in-
struction code, three address bytes and at least one data byte on Serial Data Input (DI). If the 8 least
significant address bits (A7-A0) are not all zero, all transmitted data that goes beyond the end of the
current page are programmed from the start address of the same page (from the address whose 8 least
significant bits (A7-A0) are all zero). Chip Select (CS#) must be driven Low for the entire duration of the
sequence.
The instruction sequence is shown in Figure 11. If more than 256 bytes are sent to the device, previously
latched data are discarded and the last 256 data bytes are guaranteed to be programmed correctly within
the same page. If less than 256 Data bytes are sent to device, they are correctly programmed at the
requested addresses without having any effects on the other bytes of the same page.
Chip Select (CS#) must be driven High after the eighth bit of the last data byte has been latched in,
otherwise the Page Program (PP) instruction is not executed.
As soon as Chip Select (CS#) is driven High, the self-timed Page Program cycle (whose duration is t
PP
) is
initiated. While the Page Program cycle is in progress, the Status Register may be read to check the value
of the Write In Progress (WIP) bit. The Write In Progress (WIP) bit is 1 during the self-timed Page
Program cycle, and is 0 when it is completed. At some unspecified time before the cycle is completed, the
Write Enable Latch (WEL) bit is reset.
A Page Program (PP) instruction applied to a page which is protected by the Block Protect (BP2, BP1,
BP0) bits (see Table 3.a and Table 3.b) is not executed.
相關PDF資料
PDF描述
EN25P80-50VC 4 Mbit Uniform Sector, Serial Flash Memory
EN25P80-50VCP 4 Mbit Uniform Sector, Serial Flash Memory
EN25P80-50VI 4 Mbit Uniform Sector, Serial Flash Memory
EN25P80-50VIP 4 Mbit Uniform Sector, Serial Flash Memory
EN25P80-75HC 4 Mbit Uniform Sector, Serial Flash Memory
相關代理商/技術參數
參數描述
EN25P80-50HIP 制造商:EON SILICON SOLUTION INC 功能描述:8 Mbit Uniform Sector, Serial Flash Memory
EN25P80-50VC 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:8 Mbit Uniform Sector, Serial Flash Memory
EN25P80-50VCP 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:8 Mbit Uniform Sector, Serial Flash Memory
EN25P80-50VI 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:8 Mbit Uniform Sector, Serial Flash Memory
EN25P80-50VIP 制造商:EON 制造商全稱:Eon Silicon Solution Inc. 功能描述:8 Mbit Uniform Sector, Serial Flash Memory
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*