- 您現在的位置：買賣IC網 > PDF目錄362685 > EM785840M (ELAN Microelctronics Corp .) 8-BIT MICRO-CONTROLLER PDF資料下載
參數資料
| 型號： | EM785840M |
| 廠商： | ELAN Microelctronics Corp . |
| 英文描述： | 8-BIT MICRO-CONTROLLER |
| 中文描述： | 8位微控制器 |
| 文件頁數： | 27/45頁 |
| 文件大小： | 461K |
| 代理商： | EM785840M |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁當前第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁
EM785840/5841/5842
8-bit Micro-controller
__________________________________________________________________________________________________________________________________________________________________
* This specification is subject to change without notice.
2004/11/10 V1.2
VII.5 RESET
The RESET can be caused by
(1) Power on reset
(2) WDT timeout. (if enabled and in GREEN or NORMAL mode)
(3) /RESET pin pull low (At P71S = 1).
Once the RESET occurs, the following functions are performed.
The oscillator is running, or will be started.
The Program Counter (R2) is set to all "0".
When power on, the upper 3 bits of R3 and the upper 2 bits of R4 are cleared.
The Watchdog timer and prescaler counter are cleared.
The Watchdog timer is disabled.
VII.6 Wake-up
The controller provided sleep mode for power saving :
SLEEP mode, RA(7) = 0 + "SLEP" instruction
The controller will turn off all the CPU and crystal. Other circuit with power control like key tone control or
PLL control (which has enable register), user has to turn it off by software.
Wake-up from SLEEP mode
(1) WDT time out
(2) External interrupt
(3) /RESET pull low
All these cases will reset controller , and run the program at address zero. The status just like the power on reset.
Be sure to enable circuit at case (1) or (2).
VII.7 Interrupt
RF is the interrupt status register which records the interrupt request in flag bit. IOCF is the interrupt mask
register. Global interrupt is enabled by ENI instruction and is disabled by DISI instruction. When one of the
interrupts (when enabled) generated, will cause the next instruction to be fetched from address 008H. Once in the
interrupt service routine, the source of the interrupt can be determined by polling the flag bits in the RF register.
The interrupt flag bit must be cleared in software before leaving the interrupt service routine and enabling
interrupts to avoid recursive interrupts.
相關PDF資料 |
PDF描述 |
|---|---|
| EM785840P | 8-BIT MICRO-CONTROLLER |
| EM785841 | 8-BIT MICRO-CONTROLLER |
| EM785841M | 8-BIT MICRO-CONTROLLER |
| EM785841P | 8-BIT MICRO-CONTROLLER |
| EM785842 | 8-BIT MICRO-CONTROLLER |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EM785840P | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER |
| EM785841 | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER |
| EM785841M | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER |
| EM785841P | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER |
| EM785842 | 制造商:EMC 制造商全稱:ELAN Microelectronics Corp 功能描述:8-BIT MICRO-CONTROLLER |
發布緊急采購，3分鐘左右您將得到回復。