- 您現在的位置：買賣IC網 > PDF目錄3385 > EL5175ISZ-T13 (Intersil)IC LINE RCVR SGL 550MHZ 8-SOIC PDF資料下載
參數資料
| 型號： | EL5175ISZ-T13 |
| 廠商： | Intersil |
| 文件頁數： | 2/15頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC LINE RCVR SGL 550MHZ 8-SOIC |
| 標準包裝： | 2,500 |
| 放大器類型： | 差分 |
| 電路數： | 1 |
| 轉換速率： | 900 V/µs |
| 增益帶寬積： | 200MHz |
| -3db帶寬： | 550MHz |
| 電流 - 輸入偏壓： | 12.5µA |
| 電壓 - 輸入偏移： | 3000µV |
| 電流 - 電源： | 9.6mA |
| 電流 - 輸出 / 通道： | 67mA |
| 電壓 - 電源，單路/雙路(±)： | 4.75 V ~ 11 V，±2.38 V ~ 5.5 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 帶卷 (TR) |
第1頁當前第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁
10
FN7306.7
August 25, 2010
Description of Operation and Application
Information
Product Description
The EL5175 and EL5375 are wide bandwidth, low power
and single/differential ended to single-ended output
amplifiers. The EL5175 is a single channel differential to
single-ended amplifier. The EL5375 is a triple channel
differential to single ended amplifier. The EL5175 and
EL5375 are internally compensated for closed loop gain of
+1 orgreater. Connected in gain of 1 and driving a 500
Ω
load, the EL5175 and EL5375 have a -3dB bandwidth of
550MHz. Driving a 150
Ω load at gain of 2, the bandwidth is
about 130MHz. The bandwidth at the REF input is about
450MHz. The EL5175 and EL5375 is available with a
power-down feature to reduce the power while the amplifier
is disabled.
Input, Output and Supply Voltage Range
The EL5175 and EL5375 have been designed to operate
with a single supply voltage of 5V to 10V or a split supplies
with its total voltage from 5V to 10V. The amplifiers have an
input common mode voltage range from -4.3V to 3.3V for
±5V supply. The differential mode input range (DMIR)
between the two inputs is approximately -2.3V to +2.3V. The
input voltage range at the REF pin is from -3.6V to 3.3V. If
the input common mode or differential mode signal is outside
the above-specified ranges, it will cause the output signal to
become distorted.
The output of the EL5175 and EL5375 can swing from -3.9V
to 3.5V at 500
Ω load at ±5V supply. As the load resistance
becomes lower, the output swing is reduced respectively.
Overall Gain Settings
The gain setting for the EL5175 and EL5375 is similar to the
conventional operational amplifier. The output voltage is
equal to the difference of the inputs plus VREF and then
times the gain.
Choice of Feedback Resistor and Gain Bandwidth
Product
For applications that require a gain of +1, no feedback
resistor is required. Just short the OUT+ pin to FBP pin and
OUT- pin to FBN pin. For gains greater than +1, the
feedback resistor forms a pole with the parasitic capacitance
at the inverting input. As this pole becomes smaller, the
amplifier's phase margin is reduced. This causes ringing in
the time domain and peaking in the frequency domain.
Therefore, RF has some maximum value that should not be
exceeded for optimum performance. If a large value of RF
must be used, a small capacitor in the few Pico farad range
in parallel with RF can help to reduce the ringing and
peaking at the expense of reducing the bandwidth.
The bandwidth of the EL5175 and EL5375 depends on the
load and the feedback network. RF and RG appear in
parallel with the load for gains other than +1. As this
combination gets smaller, the bandwidth falls off.
Consequently, RF also has a minimum value that should not
be exceeded for optimum bandwidth performance. For gain
of +1, RF = 0 is optimum. For the gains other than +1,
optimum response is obtained with RF between 500Ω to
1k
Ω. For AV = 2 and RF = RG = 806Ω, the BW is about
190MHz and the frequency response is very flat.
The EL5175 and EL5375 have a gain bandwidth product of
200MHz. For gains
≥5, its bandwidth can be predicted by
using Equation 2:
Driving Capacitive Loads and Cables
The EL5175 and EL5375 can drive 15pF capacitance in
parallel with 500
Ω load to ground with less than 4.5dB of
peaking at a gain of +1. If less peaking is desired in
applications, a small series resistor (usually between 5
Ω to
50
Ω) can be placed in series with each output to eliminate
most peaking. However, this will reduce the gain slightly. If
the gain setting is greater than 1, the gain resistor RG can
then be chosen to make up for any gain loss, which may be
created by the additional series resistor at the output.
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, a back-termination series resistor at the
amplifier's output will isolate the amplifier from the cable and
allow extensive capacitive drive. However, other applications
may have high capacitive loads without a back-termination
resistor. Again, a small series resistor at the output can help
to reduce peaking.
Disable/Power-Down
The EL5175 and EL5375 can be disabled and its outputs
placed in a high impedance state. The turn-off time is about
1.2s and the turn-on time is about 80ns. When disabled,
the amplifier's supply current is reduced to 80A for IS+ and
120A for IS- typically, thereby effectively eliminating the
VO
V
(
IN+VIN-VREF
+
)
1
RF
RG
--------
+
×
–
=
(EQ. 1)
-
+
-
+
Σ
G/B
VO
EN
VIN+
VIN-
VREF
FB
RG
RF
FIGURE 25.
Gain BW
200MHz
=
×
(EQ. 2)
EL5175, EL5375
相關PDF資料 |
PDF描述 |
|---|---|
| RNCP1206FTD1K30 | RES 1.3K OHM 1/2W 1% 1206 SMD |
| 228457096002026 | CONNECTOR RECEPT 64POS STR |
| SZ1SMA5923BT3G | TVS ZENER 1.5W 8.2V SMA |
| 228457048002025 | CONNECTOR RECEPT 48POS STR |
| SZ1SMA5921BT3G | TVS ZENER 1.5W 6.8V SMA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL5175ISZ-T7 | 功能描述:差分放大器 EL5175ISZ 500MHZCVR RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
| EL5175IY | 功能描述:IC LINE RCVR 550MHZ SGL 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| EL5175IY-T13 | 功能描述:IC LINE RCVR SGL 550MHZ 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| EL5175IY-T7 | 功能描述:IC LINE RCVR 550MHZ SGL 8-MSOP RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:1,000 系列:- 放大器類型:電壓反饋 電路數:4 輸出類型:滿擺幅 轉換速率:33 V/µs 增益帶寬積:20MHz -3db帶寬:30MHz 電流 - 輸入偏壓:2nA 電壓 - 輸入偏移:3000µV 電流 - 電源:2.5mA 電流 - 輸出 / 通道:30mA 電壓 - 電源，單路/雙路(±):4.5 V ~ 16.5 V，±2.25 V ~ 8.25 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:14-SOIC（0.154"，3.90mm 寬） 供應商設備封裝:14-SOIC 包裝:帶卷 (TR) |
| EL5175IYZ | 功能描述:差分放大器 EL5175IYZ 500MHZCVR RoHS:否 制造商:Texas Instruments 通道數量:1 Channel 帶寬:2.4 GHz 可用增益調整:6 dB to 26 dB 輸入補償電壓: 共模抑制比（最小值）:- 40 dB 工作電源電壓:4.75 V to 5.25 V 電源電流:100 mA 最大工作溫度:+ 85 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:WQFN-24 封裝:Reel |
發布緊急采購，3分鐘左右您將得到回復。