- 您現在的位置：買賣IC網 > PDF目錄5339 > EL5152IS (Intersil)IC OP AMP LO OFF 300MHZ 8-SOIC PDF資料下載
參數資料
| 型號： | EL5152IS |
| 廠商： | Intersil |
| 文件頁數： | 16/16頁 |
| 文件大小： | 0K |
| 描述： | IC OP AMP LO OFF 300MHZ 8-SOIC |
| 標準包裝： | 97 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 1 |
| 轉換速率： | 180 V/µs |
| 增益帶寬積： | 165MHz |
| -3db帶寬： | 270MHz |
| 電流 - 輸入偏壓： | 120nA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 3mA |
| 電流 - 輸出 / 通道： | 105mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-SOIC（0.154"，3.90mm 寬） |
| 供應商設備封裝： | 8-SOIC |
| 包裝： | 管件 |
9
FN7385.6
March 2, 2009
EL5152 Product Description
The EL5152, EL5153, EL5252, and EL5455 are wide
bandwidth, low power, low offset voltage feedback
operational amplifiers capable of operating from a single or
dual power supplies. This family of operational amplifiers are
internally compensated for closed loop gain of +1 or greater.
Connected in voltage follower mode, driving a 500
Ω load
members of this amplifier family demonstrate a -3dB
bandwidth of about 270MHz. With the loading set to
accommodate typical video application, 150
Ω load and gain
set to +2, bandwidth reduces to about 180MHz with a
600V/s slew rate. Power down pins on the EL5152 and
EL5252 reduce the already low power demands of this
amplifier family to 17A typical while the amplifier is
disabled.
Input, Output and Supply Voltage Range
The EL5152 and EL5153 families have been designed to
operate with supply voltage ranging from 5V to 12V. Supply
voltages range from ±2.5V to ±5V for split supply operation.
Of course split supply operation can easily be achieved
using single supplies by splitting off half of the single supply
with a simple voltage divider as illustrated in the application
circuit section.
Input Common Mode Range
These amplifiers have an input common mode voltage
ranging from 1.5V above the negative supply (VS- pin) to
1.5V below the positive supply (VS+ pin). If the input signal is
driven beyond this range the output signal will exhibit
distortion.
Maximum Output Swing & Load Resistance
The outputs of the EL5152 and EL5153 families maximum
output swing ranges from -4V to 4V for VS = ±5V with a load
resistance of 500
Ω. Naturally, as the load resistance
becomes lower, the output swing lowers accordingly; for
instance, if the load resistor is 150
Ω, the output swing
ranges from -3.5V to 3.5V. This response is a simple
application of Ohms law indicating a lower value resistance
results in greater current demands of the amplifier.
Additionally, the load resistance affects the frequency
response of this family as well as all operational amplifiers,
as clearly indicated by the Gain vs Frequency for Various RL
curves clearly indicate. In the case of the frequency
response reduced bandwidth with decreasing load
resistance is a function of load resistance in conjunction with
the output zero response of the amplifier.
Choosing a Feedback Resistor
A feedback resistor is required to achieve unity gain; simply
short the output pin to the inverting input pin. Gains greater
than +1 require a feedback and gain resistor to set the
desired gain. This gets interesting because the feedback
resistor forms a pole with the parasitic capacitance at the
inverting input. As the feedback resistance increases the
position of the pole shifts in the frequency domain, the
amplifier's phase margin is reduced and the amplifier
becomes less stable. Peaking in the frequency domain and
ringing in the time domain are symptomatic of this shift in
pole location. So we want to keep the feedback resistor as
small as possible. You may want to use a large feedback
resistor for some reason; in this case to compensate the shift
of the pole and maintain stability a small capacitor in the few
Pico farad range in parallel with the feedback resistor is
recommended.
For the gains greater than unity, it has been determined a
feedback resistance ranging from 500
Ω to 750Ω provides
optimal response.
Gain Bandwidth Product
The EL5156 and EL5157 families have a gain bandwidth
product of 210MHz for a gain of +5. Bandwidth can be
predicted by the following Equation 1:
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and same frequency
response as DC levels are changed at the output; this
characteristic is widely referred to as “diffgain-diffphase”.
Many amplifiers have a difficult time with this especially while
driving standard video loads of 150
Ω, as the output current
has a natural tendency to change with DC level. The EL5152
dG and dP for these families is a respectable 0.006% and
0.04%, while driving 150
Ω at a gain of 2. Driving high
impedance loads would give a similar or better dG and dP
performance as the current output demands placed on the
amplifier lessen with increased load.
Driving Capacitive Loads
The EL5152 and EL5153 families can easily drive capacitive
loads as demanding as 27pF in parallel with 500
Ω while
holding peaking to within 5dB of peaking at unity gain. Of
course if less peaking is desired, a small series resistor
(usually between 5
Ω to 50Ω) can be placed in series with the
output to eliminate most peaking. However, there will be a
small sacrifice of gain which can be recovered by simply
adjusting the value of the gain resistor.
Driving Cables
Both ends of all cables must always be properly terminated;
double termination is absolutely necessary for reflection-free
performance. Additionally, a back-termination series resistor
at the amplifier's output will isolate the amplifier from the
cable and allow extensive capacitive drive. However, other
applications may have high capacitive loads without a back-
termination resistor. Again, a small series resistor at the
output can help to reduce peaking.
Gain
BW
GainBandwidthProduct
=
×
(EQ. 1)
EL5152, EL5153, EL5252, EL5455
相關PDF資料 |
PDF描述 |
|---|---|
| 68685-308LF | CONN RCPT 8POS .100" SNG ROW |
| EL5150IS | IC OP AMP LOW OFF 200MHZ 8-SOIC |
| RGH2012-2E-P-393-B | RES 39K OHM .1% 1/4W 0805 SMD |
| 7100.1163.13 | FUSE 630MA 250V FAST 19MM PCB |
| WSLT2512R0200FEA | RES .02 OHM 1W 1% 2512 SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL5152IS-T13 | 功能描述:IC AMP VFA SGL 300MHZ 8-SOIC RoHS:否 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| EL5152IS-T7 | 功能描述:運算放大器 - 運放 LO OFF 300MHZ RoHS:否 制造商:STMicroelectronics 通道數量:4 共模抑制比（最小值）:63 dB 輸入補償電壓:1 mV 輸入偏流（最大值）:10 pA 工作電源電壓:2.7 V to 5.5 V 安裝風格:SMD/SMT 封裝 / 箱體:QFN-16 轉換速度:0.89 V/us 關閉:No 輸出電流:55 mA 最大工作溫度:+ 125 C 封裝:Reel |
| EL5152ISZ | 功能描述:IC OP AMP LO OFF 270MHZ 8-SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
| EL5152ISZT13 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:300MHz Amplifiers |
| EL5152ISZ-T13 | 功能描述:IC AMP VFA SGL 300MHZ 8-SOIC RoHS:是 類別:集成電路 (IC) >> Linear - Amplifiers - Instrumentation 系列:- 標準包裝:50 系列:- 放大器類型:通用 電路數:2 輸出類型:滿擺幅 轉換速率:1.8 V/µs 增益帶寬積:6.5MHz -3db帶寬:4.5MHz 電流 - 輸入偏壓:5nA 電壓 - 輸入偏移:100µV 電流 - 電源:65µA 電流 - 輸出 / 通道:35mA 電壓 - 電源，單路/雙路(±):1.8 V ~ 5.25 V，±0.9 V ~ 2.625 V 工作溫度:-40°C ~ 85°C 安裝類型:表面貼裝 封裝/外殼:10-TFSOP，10-MSOP（0.118"，3.00mm 寬） 供應商設備封裝:10-MSOP 包裝:管件 |
發布緊急采購，3分鐘左右您將得到回復。