- 您現在的位置：買賣IC網 > PDF目錄5331 > EL5108IW-T7 (Intersil)IC OP AMP HS VF 450MHZ SOT23-6 PDF資料下載
參數資料
| 型號： | EL5108IW-T7 |
| 廠商： | Intersil |
| 文件頁數： | 12/12頁 |
| 文件大小： | 0K |
| 描述： | IC OP AMP HS VF 450MHZ SOT23-6 |
| 標準包裝： | 3,000 |
| 放大器類型： | 通用 |
| 電路數： | 1 |
| 轉換速率： | 4500 V/µs |
| -3db帶寬： | 450MHz |
| 電流 - 輸入偏壓： | 2µA |
| 電壓 - 輸入偏移： | 3000µV |
| 電流 - 電源： | 3.7mA |
| 電流 - 輸出 / 通道： | 135mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 12 V，±2.5 V ~ 6 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SOT-23-6 |
| 供應商設備封裝： | SOT-23-6 |
| 包裝： | 帶卷 (TR) |
| 其它名稱： | EL5108IW-T7TR |
9
FN7358.7
August 10, 2010
Supply Voltage Range and Single-Supply
Operation
The EL5108 and EL5308 have been designed to operate
with supply voltages having a span of greater than or equal
to 5V and less than 12V. In practical terms, this means that
they will operate on dual supplies ranging from ±2.5V to ±5V.
With single-supply, they will operate from 5V to 10V.
As supply voltages continue to decrease, it becomes
necessary to provide input and output voltage ranges that
can get as close as possible to the supply voltages. The
EL5108 and EL5308 have an input range which extends to
within 2V of either supply. So, for example, on ±5V supplies,
the input range is about ±3V. The output range is also quite
large, extending to within 1V of the supply rail. On a ±5V
supply, the output is therefore capable of swinging from -4V
to +4V. Single-supply output range is larger because of the
increased negative swing due to the external pull-down
resistor to ground. Figure 24 shows an AC-coupled, gain of
+2, +5V single supply circuit configuration.
Video Performance
For good video performance, an amplifier is required to
maintain the same output impedance and the same
frequency response as DC levels are changed at the output.
This is especially difficult when driving a standard video load
of 150
Ω, because of the change in output current with DC
level. Previously, good differential gain could only be
achieved by running high idle currents through the output
transistors (to reduce variations in output impedance).
Special circuitry has been incorporated in the EL5108 and
EL5308 to reduce the variation of output impedance with
current output. This results in dG and dP specifications of
0.01% and 0.01°, while driving 150
Ω at a gain of 2.
Output Drive Capability
In spite of its low 3.5mA of supply current per amplifier, the
EL5108 and EL5308 are capable of providing a maximum of
±130mA of output current.
Driving Cables and Capacitive Loads
When used as a cable driver, double termination is always
recommended for reflection-free performance. For those
applications, the back-termination series resistor will
decouple the EL5108 and EL5308 from the cable and allow
extensive capacitive drive. However, other applications may
have high capacitive loads without a back-termination
resistor. In these applications, a small series resistor (usually
between 5
Ω and 50Ω) can be placed in series with the
output to eliminate most peaking.
Current Limiting
The EL5108 and EL5308 have no internal current-limiting
circuitry. If the output is shorted, it is possible to exceed the
Absolute Maximum Rating for output current or power
dissipation, potentially resulting in the destruction of the
device.
Power Dissipation
With the high output drive capability of the EL5108 and
EL5308, it is possible to exceed the +125°C Absolute
Maximum junction temperature under certain very high load
current conditions. Generally speaking when RL falls below
about 25
Ω, it is important to calculate the maximum junction
temperature (TJMAX) for the application to determine if
power supply voltages, load conditions, or package type
need to be modified for the EL5108 and EL5308 to remain in
the safe operating area. These parameters are calculated as
follows:
where:
TMAX = Maximum ambient temperature
θJA = Thermal resistance of the package
n = Number of amplifiers in the package
PDMAX = Maximum power dissipation of each amplifier in
the package
PDMAX for each amplifier can be calculated as follows:
where:
VS = Supply voltage
ISMAX = Maximum supply current of 1A
VOUTMAX = Maximum output voltage (required)
RL = Load resistance
FIGURE 23. AV = +1
-
+
325
Ω
325
Ω
IN-
IN+
FIGURE 24.
-
+
325
Ω
325
Ω
VIN
+5
0.1F
1k
0.1F
+5
VOUT
4.7F
TJMAX
TMAX θJA nPDMAX
×
()
+
=
PDMAX
2
(
VS ISMAX)
VS
(
- VOUTMAX)
VOUTMAX
RL
----------------------------
×
+
×
=
EL5108, EL5308
相關PDF資料 |
PDF描述 |
|---|---|
| 2040.0610 | FUSE 315MA 250VAC RADIAL SLOW |
| TS-709-15 | CIRCUIT BRKR THERMAL 15A 1POLE |
| TS-709-10 | CIRCUIT BRKR THERMAL 10A 1POLE |
| TS-709-15HK | CIRCUIT BRKR THERMAL 15A 1POLE |
| 956230-2000-AR-PR | CONN SOCKET 30POS 2MM VERT SMD |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL5108IW-T7A | 功能描述:特殊用途放大器 450 MHz w/ Enable RoHS:否 制造商:Texas Instruments 通道數量:Single 共模抑制比（最小值）: 輸入補償電壓: 工作電源電壓:3 V to 5.5 V 電源電流:5 mA 最大功率耗散: 最大工作溫度:+ 70 C 最小工作溫度:- 40 C 安裝風格:SMD/SMT 封裝 / 箱體:QFN-20 封裝:Reel |
| EL5108IWZ-T7 | 功能描述:高速運算放大器 EL5108IWZ SINGLE 520 MHZ FGAW ENABLE RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| EL5108IWZ-T7A | 功能描述:高速運算放大器 EL5108IWZ SINGLE 520 MHZ FGAW ENABLE RoHS:否 制造商:Texas Instruments 通道數量:1 電壓增益 dB:116 dB 輸入補償電壓:0.5 mV 轉換速度:55 V/us 工作電源電壓:36 V 電源電流:7.5 mA 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-8 封裝:Tube |
| EL5110 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Logic IC |
| EL5111 | 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:60MHz Rail-to-Rail Input-Output Op Amps |
發布緊急采購，3分鐘左右您將得到回復。