參數資料
型號： EL2157CS-T13
廠商： INTERSIL CORP
元件分類： 音頻／視頻放大
英文描述： 125MHz Single Supply, Clamping Op Amps
中文描述： 1 CHANNEL, VIDEO AMPLIFIER, PDSO8
封裝： SO-8
文件頁數： 6/20頁
文件大?。?/td> 488K
代理商： EL2157CS-T13
EL2150CEL2157C
125 MHz Single Supply Clamping Op Amps
Applications Information
Contd
Output Voltage Clamp
The EL2157C amplifier has an output voltage
clamp This clamping action is fast being acti-
vated almost instantaneously and being deacti-
vated in k 7 ns and prevents the output voltage
from going above the preset clamp voltage This
can be very helpful when the EL2157C is used to
drive an AD converter as some converters can
require long times to recover if overdriven The
output voltage remains at the clamp voltage level
as long as the product of the input voltage and
the gain setting exceeds the clamp voltage If the
EL2157C is connected in a gain of 2 for example
and a3V DC is applied to the CLAMP pin any
voltage higher than a15V at the inputs will be
clamped and a3V will be seen at the output
Figure 1 below is a unity gain connected
EL2157C being driven by a 3Vp-p sinewave with
225V applied to the CLAMP pin The resulting
output waveform with its output being clamped
to 225V is shown in Figure 2
2150 – 59
Figure 1
2150 – 60
Figure 2
Figure 3 shows the output of the same circuit
being driven by a 05V to 275V square wave as
the clamp voltage is varied from 10V to 25V as
well as the unclamped output signal The rising
edge of the signal is clamped to the voltage ap-
plied to the CLAMP pin almost instantaneously
The output recovers from the clamped mode
within5-7ns depending on the clamp voltage
Even when the CLAMP pin is taken 02V below
the minimum 12V specified the output is still
clamped and recovers in about 11 ns
2150 – 61
Figure 3
The clamp accuracy is affected by 1) the CLAMP
pin voltage 2) the input voltage and 3) the load
resistor Depending upon the application the ac-
curacy may be as little as a few tens of millivolts
to a few hundred millivolts Be sure to allow for
these inaccuracies when choosing the clamp volt-
age Curves of Clamp Accuracy vs VCLAMP and
VIN for 3 values of RL are included in the Typi-
cal Performance Curves Section
Unlike amplifiers that clamp at the input and are
therefore limited to non-inverting applications
only
the EL2157C output clamp architecture
works for both inverting and non-inverting gain
applications There is also no maximum voltage
difference limitation between VIN and VCLAMP
which is common on input clamped architec-
tures
The voltage clamp operates for any voltage be-
tween a12V above the GND pin and the mini-
mum output voltage swing VOP Forcing the
CLAMP pin much below a12V can saturate
transistors and should therefore be avoided
14
相關PDF資料
PDF描述
EL2157CS-T7 125MHz Single Supply, Clamping Op Amps
EL2286CN 250MHz/3mA Current Mode Feedback Amp w/Disable
EL2286CS 250MHz/3mA Current Mode Feedback Amp w/Disable
EL5327CLZ-T13 2.5MHz 4, 8, 10 & 12 Channel Rail-to-Rail Buffers
EL5327CLZ-T7 2.5MHz 4, 8, 10 & 12 Channel Rail-to-Rail Buffers
相關代理商/技術參數
參數描述
EL2157CS-T7 制造商:INTERSIL 制造商全稱:Intersil Corporation 功能描述:125MHz Single Supply, Clamping Op Amps
EL215K12-Z 制造商:Fujisoku 功能描述:Rocker switch,miniature,DPST,ON-OFF,15A
EL215K-Z 制造商:Fujisoku 功能描述:Rocker switch
EL215-V 功能描述:晶體管輸出光電耦合器 Optocouplers RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk
EL216 功能描述:晶體管輸出光電耦合器 Optocouplers RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*