- 您現在的位置：買賣IC網 > PDF目錄3290 > EL2126CWZ-T7A (Intersil)IC AMP WIDEBAND LN LP SOT23-5 PDF資料下載
參數資料
| 型號： | EL2126CWZ-T7A |
| 廠商： | Intersil |
| 文件頁數： | 8/19頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC AMP WIDEBAND LN LP SOT23-5 |
| 標準包裝： | 250 |
| 放大器類型： | 電壓反饋 |
| 電路數： | 1 |
| 轉換速率： | 150 V/µs |
| -3db帶寬： | 135MHz |
| 電流 - 輸入偏壓： | 7µA |
| 電壓 - 輸入偏移： | 500µV |
| 電流 - 電源： | 5mA |
| 電流 - 輸出 / 通道： | 220mA |
| 電壓 - 電源，單路/雙路(±)： | 5 V ~ 30 V，±2.5 V ~ 15 V |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | SC-74A，SOT-753 |
| 供應商設備封裝： | SOT-23-5 |
| 包裝： | 帶卷 (TR) |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁當前第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁
16
FN7046.4
May 2, 2007
Output Drive Capability
The EL2126 is designed to drive low impedance load. It can
easily drive 6VP-P signal into a 100Ω load. This high output
drive capability makes the EL2126 an ideal choice for RF, IF,
and video applications. Furthermore, the EL2126 is
current-limited at the output, allowing it to withstand
momentary short to ground. However, the power dissipation
with output-shorted cannot exceed the power dissipation
capability of the package.
Driving Cables and Capacitive Loads
Although the EL2126 is designed to drive low impedance
load, capacitive loads will decreases the amplifier's phase
margin. As shown in the performance curves, capacitive
load can result in peaking, overshoot and possible
oscillation. For optimum AC performance, capacitive loads
should be reduced as much as possible or isolated with a
series resistor between 5
Ω to 20Ω. When driving coaxial
cables, double termination is always recommended for
reflection-free performance. When properly terminated, the
capacitance of the coaxial cable will not add to the capacitive
load seen by the amplifier.
Power Supply Bypassing And Printed Circuit
Board Layout
As with any high frequency devices, good printed circuit
board layout is essential for optimum performance. Ground
plane construction is highly recommended. Lead lengths
should be kept as short as possible. The power supply pins
must be closely bypassed to reduce the risk of oscillation.
The combination of a 4.7F tantalum capacitor in parallel
with 0.1F ceramic capacitor has been proven to work well
when placed at each supply pin. For single supply operation,
where pin 4 (VS-) is connected to the ground plane, a single
4.7F tantalum capacitor in parallel with a 0.1F ceramic
capacitor across pins 7 (VS+) and pin 4 (VS-) will suffice.
For good AC performance, parasitic capacitance should be
kept to a minimum. Ground plane construction again should
be used. Small chip resistors are recommended to minimize
series inductance. Use of sockets should be avoided since
they add parasitic inductance and capacitance which will
result in additional peaking and overshoot.
Supply Voltage Range and Single Supply
Operation
The EL2126 has been designed to operate with supply
voltage range of ±2.5V to ±15V. With a single supply, the
EL2126 will operate from +5V to +30V. Pins 4 and 7 are the
power supply pins. The positive power supply is connected
to pin 7. When used in single supply mode, pin 4 is
connected to ground. When used in dual supply mode, the
negative power supply is connected to pin 4.
As the power supply voltage decreases from +30V to +5V, it
becomes necessary to pay special attention to the input
voltage range. The EL2126 has an input voltage range of
0.4V from the negative supply to 1.2V from the positive
supply. So, for example, on a single +5V supply, the EL2126
has an input voltage range which spans from 0.4V to 3.8V.
The output range of the EL2126 is also quite large, on a +5V
supply, it swings from 0.4V to 3.8V.
EL2126
相關PDF資料 |
PDF描述 |
|---|---|
| 0741620216 | CONN RCPT R/A 16POS 2.54MM GOLD |
| EL5103IWZ-T7A | IC VFA SLEW SNGL 400MHZ SOT23-5 |
| 87987-6 | 06 MODI BDMNT RCPT SR .156CL |
| LT1638HS8#TRPBF | IC OPAMP R-R IN/OUT DUAL 8-SOIC |
| ISL55191IBZ | IC OPAMP ULT L-NOISE/DIST 8-SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EL21278 PC93 | 制造商:YARWAY 功能描述: |
| EL212-V | 功能描述:晶體管輸出光電耦合器 Optocouplers RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk |
| EL213 | 功能描述:晶體管輸出光電耦合器 Optocouplers RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk |
| EL213(TA) | 功能描述:晶體管輸出光電耦合器 Optocouplers RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk |
| EL213(TA)-V | 功能描述:晶體管輸出光電耦合器 Optocouplers RoHS:否 制造商:Vishay Semiconductors 輸入類型:DC 最大集電極/發射極電壓:70 V 最大集電極/發射極飽和電壓:0.4 V 絕緣電壓:5300 Vrms 電流傳遞比:100 % to 200 % 最大正向二極管電壓:1.65 V 最大輸入二極管電流:60 mA 最大集電極電流:100 mA 最大功率耗散:100 mW 最大工作溫度:+ 110 C 最小工作溫度:- 55 C 封裝 / 箱體:DIP-4 封裝:Bulk |
發布緊急采購，3分鐘左右您將得到回復。