
Pb
RoHS
EL13C5J2F-125.000M TR
EL13C5 J 2 F -125.000M TR
Series
RoHS Compliant (Pb-free) 3.3V 6 Pad 3.2mm x 5mm
Ceramic SMD LVDS Oscillator
Frequency Tolerance/Stability
±25ppm Maximum over -40°C to +85°C
Duty Cycle
50 ±5(%)
Packaging Options
Tape & Reel
Nominal Frequency
125.000MHz
Logic Control / Additional Output
Tri-State and Complementary Output
ELECTRICAL SPECIFICATIONS
Nominal Frequency
125.000MHz
Frequency Tolerance/Stability
±25ppm Maximum over -40°C to +85°C (Inclusive of all conditions: Calibration Tolerance (at 25°C),
Frequency Stability over the Operating Temperature Range, Supply Voltage Change, Output Load Change,
First Year Aging at 25°C, Shock, and Vibration)
Supply Voltage
+3.3Vdc ±5%
Input Current
66mA Maximum
Output Voltage Logic High (Voh)
1.43Vdc Typical, 1.6Vdc Maximum
Output Voltage Logic Low (Vol)
1.1Vdc Typical, 0.9Vdc Minimum
Differential Output Voltage (Vod)
247mV Minimum, 330mV Typical, 454mV Maximum
Offset Voltage (Vos)
1.125V Minimum, 1.250V Typical, 1.375V Maximum
Rise/Fall Time
300pSec Typical, 700pSec Maximum (Measured over 20% to 80% of waveform)
Differential Output Error (dVod)
50mV Maximum
Duty Cycle
50 ±5(%) (Measured at 50% of waveform or at the crossing point)
Offset Error (dVos)
150mV Maximum
Output Swing (dVOpp)
350mVdc Minimum
Load Drive Capability
100 Ohms Between Output and Complementary Output
Output Logic Type
LVDS
Phase Noise
-60dBc/Hz at 10Hz Offset, -95dBc/Hz at 100Hz Offset, -125dBc/Hz at 1kHz Offset, -143dBc/Hz at 10kHz
Offset, -145dBc/Hz at 100kHz Offset, -145dBc/Hz at 1MHz Offset, -146dBc/Hz at 10MHz Offset (All Values
are Typical, Fo=156.250MHz)
Logic Control / Additional Output
Tri-State and Complementary Output
Tri-State Input Voltage (Vih and Vil)
Vih of 70% of Vcc Minimum or No Connect to Enable Output and Complementary Output, Vil of 30% of Vcc
Maximum to Disable High Impedance Output and Complementary Output
Standby Current
30A Maximum (Without Load)
RMS Phase Jitter
0.4pSec Typical, 1pSec Maximum (Fj=12kHz to 20MHz)
Start Up Time
10mSec Maximum
Storage Temperature Range
-55°C to +125°C
ENVIRONMENTAL & MECHANICAL SPECIFICATIONS
ESD Susceptibility
MIL-STD-883, Method 3015, Class 1, HBM: 1500V
Fine Leak Test
MIL-STD-883, Method 1014, Condition A
Flammability
UL94-V0
Gross Leak Test
MIL-STD-883, Method 1014, Condition C
Mechanical Shock
MIL-STD-883, Method 2002, Condition B
Moisture Resistance
MIL-STD-883, Method 1004
Moisture Sensitivity
J-STD-020, MSL 1
Resistance to Soldering Heat
MIL-STD-202, Method 210, Condition K
Resistance to Solvents
MIL-STD-202, Method 215
Solderability
MIL-STD-883, Method 2003
Temperature Cycling
MIL-STD-883, Method 1010, Condition B
Vibration
MIL-STD-883, Method 2007, Condition A
www.ecliptek.com | Specification Subject to Change Without Notice | Rev C 8/14/2010 | Page 1 of 6