參數資料
型號： Edge142
廠商： Semtech Corporation
英文描述： Per Pin timing Deskew w 4x2 Cross Point Switch
中文描述： 每個引腳的時間糾偏瓦特4x2交叉點開關
文件頁數： 8/19頁
文件大?。?/td> 179K
代理商： EDGE142
8
2000 Semtech Corp.
www.semtech.com
EDGE HIGH-PERFORMANCE PRODUCTS
Circuit Description
(continued)
Edge142
Analog Delay Inputs
VDELAY, VFALL, and VMID are analog voltage inputs which
control the delay of the rising and falling edge. All three
inputs may vary from +0.1V (minimum delay) to -1.3V
(maximum delay).
VMID should be permanently set to the middle of the
overall voltage range spanned by VFALL (~ -0.6V). A
fixed resistor to ground will usually suffice.
The exact
setting of VFALL will vary depending on the required delay
range of the falling edge.
These inputs are designed to sink a constant input
current, typically 1.0 mA (with REXT1 = 2.94 K
), over
their operating range from +0.1V to -1.3V. Any voltage
DAC used to drive these inputs directly needs to source
at least 1.0 mA. Any current DAC used needs to factor
in the constant 1.0 mA input current.
The equation used to establish the VDELAY, VMID, and
VFALL input currents is:
I (VFALL, VDELAY, VMID) = 3.0V / REXT1.
The fact that the VDELAY, VFALL, and VMID inputs have
internal current sources allows a voltage DAC capable
of generating only positive voltages and an external
resistor network to be pulled down to the Edge142's
negative input voltage compliance. These current
sources are designed to be constant over temperature,
so changes in system temperature will not translate into
a delay voltage shift.
Using a different REXT1 will program a different input
current. However the value of this current does not
affect deskew range or performance. The ability to vary
this current allows a more flexible interface to a variety
of DAC programming techniques.
VDELAY, VFALL, and VMID all require current flow. Do
NOT leave any of these input pins floating. If an
application does not require any falling edge delay,
connect all VDELAY and VMID pins to ground.
Compensation Pins
COMP1 and COMP2 are Op Amp compensation pins.
For proper Edge142 functionality, these pins require a
.1
μ
F capacitor to ground.
Thermal Monitor
The Edge142 includes an on-chip thermal monitor
accessible through the pins TDP and TDN. These nodes
connect to five diodes in series (see Figure 6) and may
be used to accurately measure the junction temperature
at any time.
Figure 6. Thermal Diode String
An external bias current of 100
μ
A is injected through
the string, and the measured voltage corresponds to a
specific junction temperature with the following equation:
TJ(
C) = {(V(TDP)
–
V(TDN)) / 5
–
.7} / (-.00208).
Bias Current
Temperature coefficient = –10 mV/
C
TDP
TDN
相關PDF資料
PDF描述
Edge646 Pin Electronics Driver, Window Comparator, and Switch Matrix(用于自動測試設備的引腳電子驅動器,窗式比較器和開關陣列)
Edge647 Pin Electronics Driver, Window Comparator, and Switch Matrix(用于自動測試設備的引腳電子驅動器,窗式比較器和開關陣列)
Edge649 Single Supply RS232C Line Driver/Receiver(?????μ?o?RS232C ?o?????????¨???2???2??????)
Edge692 Connector
Edge693 500 MHz Monolithic Dual Pin Electronics Driver
相關代理商/技術參數
參數描述
EDGE211 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Dual Pin Electronics Driver
EDGE-300 制造商:ADVANTECH 制造商全稱:Advantech Co., Ltd. 功能描述:USB-Type Quad-band EDGE Dongle
EDGE4707B 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Quad Channel Per-Pin Precision Measurement Unit
EDGE4717D 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:Quad Channel, Per Pin Precision Measurement Unit
EDGE629 制造商:SEMTECH 制造商全稱:Semtech Corporation 功能描述:1 GHz Timing Deskew and Quad Fanout Element
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*