- 您現在的位置：買賣IC網 > PDF目錄93289 > EB02 Industrial Control IC PDF資料下載
參數資料
| 型號： | EB02 |
| 英文描述： | Industrial Control IC |
| 中文描述： | 工業控制IC |
| 文件頁數： | 4/4頁 |
| 文件大小： | 101K |
| 代理商： | EB02 |
APEX MICROTECHNOLOGY CORPORATION 5980 NORTH SHANNON ROAD TUCSON, ARIZONA 85741 USA APPLICATIONS HOTLINE: 1 (800) 546-2739
4
This data sheet has been carefully checked and is believed to be reliable, however, no responsibility is assumed for possible inaccuracies or omissions. All speciciations are subject to change without notice.
EBO2U REV. B JANUARY 2001 2001 Apex Microtechnology Corporation
EB02
OPERATING
CONSIDERATIONS
POWER SUPPLY REQUIREMENTS
SUPPLY
VOLTAGE
MAX CURRENT
HV1
10V to 100V
10A, continuous, 20A peak
HV2
10V to 100V
10A, continuous, 20A peak
HV3
10V to 100V
10A, continuous, 20A peak
Vcc1
10V to 20V
10mA
Vcc2
10V to 20V
10mA
Vcc3
10V to 20V
10mA
Vdd
4.5 to 20V
10mA
HV1, HV2, and HV3 may be used independently, or may
be one supply. Also Vcc1, Vcc2, and Vcc3 may be used
independently or tied together. The Vdd supply must be
compatible with the input logic. If a high voltage logic such as
CMOS is used it may be tied with the Vcc supplies. HCMOS
requires a 5V±10% supply
SPECIAL CONSIDERATIONS
GENERAL
The EB02 is designed to give the user maximum exibility
in a digital or DSP based motion control system. Thermal,
overvoltage, overcurrent, and crossre protection circuits are
part of the user’s design.
Users should read Application Note 1, "General Operating
Considerations;” and Application Note 30, “PWM Basics”
for much useful information in applying this part. These
Application Notes are in the “Power Integrated Circuits Data
Book” and on line at www.apexmicrotech.com.
GROUNDING AND BYPASSING
As in any high power PWM system, grounding and
bypassing are some of the keys to success. The EB02 is
capable of generating 2 kW pulses with 40 n-second rise and
fall times. If improperly grounded or bypassed this can cause
horrible conducted and radiated EMI.
In order to reduce conducted EMI, the EB02 provides a
separate power ground, named HVRTN, for each high voltage
supply. These grounds are electrically isolated from the logic
ground and each other. This isolation eliminates high current
ground loops. However, more than 5V offset between the
grounds will destroy the EB02. Apex recommends back
to back high current diodes between logic and power
grounds; this will maintain isolation but keep offset at a
safe level. All grounds should tie together at one common
point in the system.
In order to reduce radiated EMI, Apex recommends a 100
F or larger capacitor between HV and HVRTN. This capacitor
should be a switching power grade capacitor with ESR rated
at 20kHz. This capacitor should be placed physically as close
to the EB02 as possible.
However, such a capacitor will typically have a few
hundred milli-ohms or so ESR.
Therefore, each section
must also be bypassed with a low ESR 1F or larger
ceramic capacitor.
In order to minimize radiated noise, it is necessary to
minimize the area of the loop containing high frequency
current. (The size of the antenna.) Therefore, the 1F
ceramic capacitors should bypass each HV to its return at
the pins of the EB02.
SHOOT THROUGH PROTECTION
Power FETs have a relatively short turn on delay, and a
long turn off delay. Therefore, if the turn on input to an FET in
a half bridge circuit is applied simultaneously with the turn off
input to the other FET in that half bridge, there will be a time
when both FETs are simultaneously on. This "shoot through
condition" will short the power rails through the FETs, causing
excessive power dissipation and very high EMI.
To avoid the shoot through condition the turn on of one FET
must be delayed long enough for the other FET in the same
half bridge to have completely turned off.
A delay of at least 0.5 -seconds is required for the EB02.
This delay is required for both the Hin and Lin inputs.
PROTECTION CIRCUITS
The EB02 does not include protection circuits.
However, there is a shut down input which will turn off all
FETs when at logic “1”. This input may be used with user
designed temperature sensing and current sensing circuits
to shut down the FETs in the event of a detected unsafe
condition. This is recommended since the FETs may be
turned off this way even if the normal input logic or DSP
programming is faulty.
START UP CONSIDERATIONS
The lower rail FET in the half bridge must be turned on
for at least 2 -seconds to charge the bootstrap capacitor
before the top rail FET can be turned on. This must be done
no more than 330 -seconds prior to turning on the top rail
FET. However, a grounded load will give the same purpose
as turning on the lower rail FET. However a grounded load
will give the same purpose as turning on the lower rail
FET. Therefore a grounded load may be operated without
this consideration.
An internal oating supply is used to enhance the operation
of the bootstrap bias circuit. This allows the top rail FETs to
be held on indenitely once turned on.
HEATSINK
The EB02 should be provided with sufcient heatsink to
dissipate 51 watts when operating at 100V, 10A, 50kHz and 3
sections simultaneously providing maximum current.
The dissipation is composed of conduction losses (IoutxVsat)
up to 16 watt per half bridge and switching losses of about 1
watt per half bridge. The conduction losses are proportional
to Iout; switching losses are proportional to HV supply voltage,
load capacitance, and switching frequency.
相關PDF資料 |
PDF描述 |
|---|---|
| EB1411 | Analog IC |
| EB3110 | Analog IC |
| EB3200 | Analog IC |
| EB3210 | Analog IC |
| EB3310 | Analog IC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| EB020FL210GB0W | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Aluminum Capacitors Axial Non-Polar Capacitor Styles |
| EB020FL210JB0W | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Aluminum Capacitors Axial Non-Polar Capacitor Styles |
| EB020FL222GB0W | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Aluminum Capacitors Axial Non-Polar Capacitor Styles |
| EB020FL247DB0W | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Aluminum Capacitors Axial Non-Polar Capacitor Styles |
| EB020GD247JB0W | 制造商:VISHAY 制造商全稱:Vishay Siliconix 功能描述:Aluminum Capacitors Axial Non-Polar Capacitor Styles |
發布緊急采購，3分鐘左右您將得到回復。