- 您現在的位置：買賣IC網 > PDF目錄362592 > E712545 (Fujitsu Limited) 8-bit Proprietary Microcontroller PDF資料下載
參數資料
| 型號： | E712545 |
| 廠商： | Fujitsu Limited |
| 元件分類： | 8位微控制器 |
| 英文描述： | 8-bit Proprietary Microcontroller |
| 中文描述： | 8位微控制器專有 |
| 文件頁數： | 14/48頁 |
| 文件大小： | 546K |
| 代理商： | E712545 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁當前第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁
MB89960 Series
14
I
HANDLING DEVICES
1.
Do not exceed maximum rated voltage (to prevent latch-up)
Latch-up may occur on CMOS ICs if voltage higher than V
CC
or lower than V
SS
is applied to input or output pins
other than medium- and high voltage pins or if the voltage applied between V
CC
and V
SS
higher the rating.
If latch-up occurs, the power supply current increases rapidly resulting in thermal damage to circuit elements.
Therefore, ensure that maximum ratings are not exceeded in circuit operation.
Similarly, when turning the analog power supply on or off, ensure the analog power supply voltages (AV
CC
and
AVR) and analog input voltages do not exceed the digital power supply (V
CC
) .
2.
Power supply voltage fluctuations
Rapid fluctuation of the voltage may cause the device to misoperate, even if the voltage remains within the
allowed operating range.
The standard for power supply voltage stability is a peak-to-peak V
CC
ripple voltage at the mains supply frequency
(50 to 60 Hz) of 10
%
or less of V
CC
and a transient voltage change rate of 0.1 V/ms or less such as when turning
the power supply on or off.
3.
Treatment of unused input pins
Leaving unused input pins unconnected can cause misoperation or permanent damage to the device due to
latchup. Always pull-up or pull-down unused input pins using a 2 k
or larger resistor.
If some I/O pins are unused, either set as outputs and leave open circuit or set as inputs and treat in the same
way as input pins.
4.
Treatment of N.C. pins
Always leave N.C. (internally connected) pins open.
5.
Treatment of power supply pins on microcontrollers with an A/D converter
Even if not using the A/D converter, connect to be AV
CC
=
V
CC
and AV
SS
=
AVR
=
V
SS
.
6.
Precautions on using an external clock
An oscillation stabilization delay occurs after a power-on reset or when recovering from sub-clock or stop mode,
even if an external clock is used.
相關PDF資料 |
PDF描述 |
|---|---|
| E713704 | 16-bit Proprietary Microcontroller |
| E72-12V | Engineering Catalog 169 |
| E72-5V | Engineering Catalog 169 |
| E73-12V | Engineering Catalog 169 |
| E73-5V | Engineering Catalog 169 |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E71307-000 | 制造商:TE Connectivity 功能描述:TX40AB90-1008H 制造商:TE Connectivity 功能描述:TX40AB90-1008H - Bulk |
| E71365-000 | 制造商:TE Connectivity 功能描述:TMS-SCE-2X-1K-3/32-2.0-4 - Bulk 制造商:TE Connectivity 功能描述:TMS-SCE-2X-1K-3/32-4 |
| E713704 | 制造商:FUJITSU 制造商全稱:Fujitsu Component Limited. 功能描述:16-bit Proprietary Microcontroller |
| E71-3C90 | 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:E cores and accessories |
| E71-3C90-E100 | 制造商:FERROXCUBE 制造商全稱:Ferroxcube International Holding B.V. 功能描述:E cores and accessories |
發布緊急采購，3分鐘左右您將得到回復。