參數資料
型號: E647-EDGE647
英文描述: Pin Electronics Driver. Window Comparator. and Switch Matrix
中文描述: 引腳電子驅動程序。窗口比較器。和開關矩陣
文件頁數: 8/13頁
文件大小: 138K
代理商: E647-EDGE647
4
2000 Semtech Corp.
www.semtech.com
EDGE HIGH-PERFORMANCE PRODUCTS
Edge647
the DUT. In this environment, the driver can withstand a
short to any legal DUT voltage for an indefinite period.
In a low impedance application with no additional output
series resistance, care must be exercised and systems
should be designed to check for this condition and tristate
the driver if a short is detected.
The driver does NOT have on-chip short circuit protection
or limitation circuitry.
VBB
VBB is an analog input which establishes the threshold
for all single ended digital input signals.
If SW0 EN*,
SW1 EN*, or SW2 EN* are more positive than VBB, these
inputs are a digital “1".
Conversely, if they are more
negative than VBB, they are a “0".
All digital inputs are wide voltage comparator inputs, so
they are technology independent.
By establishing the
appropriate VBB level for the switch control inputs, and
the appropriate differential input levels for the driver digital
control inputs, the Edge647 may be driven by TTL, ECL,
CMOS, or any custom level circuitry.
Figure 1. Driver Digital Inputs
Figure 2. Driver Differential Digital Inputs
Circuit Description
Driver Description
The Edge647 driver supports three distinct programmable
driver levels; high, low, and termination,
and high
impedance. There are no restrictions between any of these
three levels in that all three may vary independently over
the entire operating voltage range between VCC and VEE.
The DVR EN*, DATA, and VTT EN pins are digital inputs
that control the driver (see Table 1). With DVR EN* low,
DATA determines whether the driver will force VH or VL at
DOUT. With DVR EN* high, VTT EN* controls whether the
driver goes into high impedance or drives VTT.
Table 1. Driver Truth Table
VH, VL, and VTT
VH, VL, and VTT define the logical “1”, “0”, and
“termination” levels of the driver and can be adjusted
anywhere over the range spanned by VCC to VEE. There
is no restriction between VH, VL, and VTT, in that they can
all vary independently over the entire voltage range
determined by the power supply levels.
The VH, VL, and VTT inputs are unbuffered in that they
also provide the driver output current, so the sources of
these voltages must have ample current drive capability.
While VTT is referred to as the termination voltage, it may
also be used as a very high “programming” level on many
memory devices.
Driver Output Protection
The Edge647 is designed to operate in a functional testing
environment where a controlled impedance (typically 50
) is maintained between the pin electronics and the DUT.
In general, there will be an external resistor at the driver
output which series terminates the transmission line to
*
N
E
R
V
DN
E
T
VA
T
A
DT
U
O
D
10
X
Z
i
H
11
X
T
V
0X0
L
V
0X1
H
V
SW0 EN*
SW1 EN*
SW2 EN*
VBB
DATA
DATA*
DVR EN*
DVR EN
VTT EN
VTT EN*
相關PDF資料
PDF描述
E649-EDGE649 Octal Pin Electronics Driver / Receiver
E670-EDGE670 500 MHz Window Comparator
E672-EDGE672 500 MHz Pin Electronics Window Comparator and Load
E692-EDGE692 200 MHz Monolithic Dual Pin Electronics Driver
E693-EDGE693 500 MHz Monolithic Dual Pin Electronics Driver
相關代理商/技術參數
參數描述
E64808-000 制造商:TE Connectivity 功能描述:VARISTOR 39V 10MM RADIAL T/R 制造商:TE Connectivity 功能描述:VARISTOR 39V 3.5KA DISC 10MM
E64809-000 制造商:TE Connectivity 功能描述:CBL 3CNDCTR 20AWG NKL PLTD CPPR WH 600V - Cable Rools/Shrink Tubing 制造商:TE Connectivity 功能描述:55PC1233-20-9/93/96-9
E6485 功能描述:BOARD EVALUATION FOR QT60485 制造商:microchip technology 系列:Quantum 零件狀態:停產 傳感器類型:- 感應范圍:- 接口:- 靈敏度:- 電壓 - 電源:- 嵌入式:- 所含物品:板 使用的 IC/零件:- 標準包裝:1
E6486 功能描述:觸摸傳感器開發工具 Eval Board for QT60326/486 Series RoHS:否 制造商:Cypress Semiconductor 工具用于評估: 接口類型: 工作電壓: 最大工作溫度:
E6486 制造商:Quantum Corp 功能描述:KITTOUCH SENSOR 48 CH EVAL