- 您現在的位置：買賣IC網 > PDF目錄362584 > E3MC-MA41 (Electronic Theatre Controls, Inc.) RGB Color Sensor PDF資料下載
參數資料
| 型號： | E3MC-MA41 |
| 廠商： | Electronic Theatre Controls, Inc. |
| 英文描述： | RGB Color Sensor |
| 中文描述： | RGB顏色傳感器 |
| 文件頁數： | 25/26頁 |
| 文件大?。?/td> | 674K |
| 代理商： | E3MC-MA41 |
E3MC
E3MC
Precautions
AVOID DAMAGE TO THE E3MC
Voltage must not exceed the rated voltage of the E3MC.
When supplying power to the E3MC, make sure that the
polarity of the power is correct.
Do not short-circuit the load connected to the E3MC.
INSTALLATION
Power Up Ready
The E3MC is ready to sense objects 100 ms after the unit is
turned ON.
The 100 ms wait is also required when the E3MC output is
controlling other devices.
If power is supplied to the E3MC and the load independently,
be sure to turn ON the E3MC first
When the E3MC is turned ON or OFF, the operation indicator
will be illuminated for an instant, but no control output will be
turned ON.
Power Off
The E3MC may output a single pulse when the control power
supply is turned OFF. If the E3MC is connected to a timer or
counter, you should supply power to the timer or counter from
the same power supply as the E3MC.
Power Supplies
Power supply must be filtered with 10% MAX ripple (see
supply voltage specification).
When a switching regulator is required, you must connect the
FG (frame ground) and G (ground) terminals together, eliminat-
ing the switching noise of the regulator to avoid a malfunction.
WIRING
Cable
The cable can be extended up to 100 m, allowing for a cable
thickness of 0.3 mm
2
maximum.
The cable must not be repeatedly bent.
Do not pull cables with pulling forces exceeding 50 N
(11.24 lb
force).
M12 Metal Connector
When connecting or disconnecting the cable, first remove the
power to the E3MC.
To avoid damage, tighten the metal connector securely by
hand. Do not use any tools.
To ensure that the enclosure rating is maintained (so that
water/vibration ratings are assured), the cable connector
must be securely hand-tightened.
Avoid Damage or Malfunction Due to Induction Noise
Never run the E3MC Color Sensor cables in the same con-
duit with power lines or high tension cables.
FURTHER INFORMATION
Correcting an EEPROM Error
An EEPROM error may result if the power supplied to the
Sensor fails, or if the Sensor is influenced by static noise.
When an EEPROM error occurs, the operation and bank
indicators will flash and the buzzer will beep. The remedy is
to reprogram and make threshold level settings again.
相關PDF資料 |
PDF描述 |
|---|---|
| E3MC-MX11 | RGB Color Sensor |
| E3MC-MX41 | RGB Color Sensor |
| E3MC-MY11 | RGB Color Sensor |
| E3MC-MY41 | RGB Color Sensor |
| E3MC-X11 | RGB Color Sensor |
相關代理商/技術參數 |
參數描述 |
|---|---|
| E3MCMX11 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:RGB FIBER OPTIC NPN 4 OUTPUT |
| E3MC-MX11 | 功能描述:光電傳感器 RGB FIBER OPTIC NPN 4 OUTPUT RoHS:否 制造商:Omron Industrial 感應方式:Retroreflective 感應距離:2 m 光源:Infrared LED 放大器類型: 連接:Prewired Cable 輸出配置:Light ON |
| E3MCMX41 | 制造商:OMRON AUTOMATION AND SAFETY 功能描述:RGB FIBER OPTIC PNP 4 OUTPUT |
| E3MC-MX41 | 功能描述:光電傳感器 RGB FIBER OPTIC PNP 4 OUTPUTS RoHS:否 制造商:Omron Industrial 感應方式:Retroreflective 感應距離:2 m 光源:Infrared LED 放大器類型: 連接:Prewired Cable 輸出配置:Light ON |
| E3MCMX41NR | 制造商:Omron Corporation 功能描述: |
發布緊急采購，3分鐘左右您將得到回復。