
DSTINIs400/DSTINIs-00x Sockets Evaluation Board
2 of 11
COMPONENT LIST (continued)
DESIGNATION
C16, C18
QTY
2
DESCRIPTION
270pF capacitor (1206)
1nF, 2kV thru-hole
capacitors
27pF capacitors (1206)
1N5908 D0-201
BAT54 SOT-23
SODIMM144
Hirose SX6E-144S-0.8SH
2.5mm center, 5.5mm
outside barrel connector
RJ-45 modular jack
3 x 1-pin headers, 0.1
centers
DB9 serial female
DB9 serial male
Pad jumper
RJ11 modular jack
22 H inductor
205k , ±1% resistor (1206)
121k , ±1% resistor (1206)
C20–C22
3
C23, C24
D1
D2
2
1
1
J1
1
J2
1
J7
1
J9–J11
3
J12
J13
J14
J16
L1
R1
R2
1
1
1
1
1
1
1
R4–R7, R8,
R10–R12
R13, R9
R14
R15, R17, R18
R16
R19
8
49.9 , ±1% resistors (1206)
2
1
3
1
1
47 resistor (1206)
22.1k , ±1% resistor (1206)
220 resistors (1206)
10k resistor (1206)
Pad jumper
DESIGNATION
R20
R21
R22, R23
R24
QTY
1
1
2
1
DESCRIPTION
47k resistor (1206)
124 , ±1% resistor (1206)
1k resistor (1206)
10k resistor (1206)
BelFuse S558-5999-T7
transformer
MAX1692 PWM step-down
regulator
Intel LXT972ALC Ethernet
PHY
Dialight 597-7741 LED
MAX560CAI transceiver
DS2480B serial 1-Wire line
driver
DS9502 ESD protection
diode
25.000MHz, HC49
Ferrite Bead, Fair-Rite
2512067007Y3
T1
1
U1
1
U3
1
U4–U6
U7
3
1
U8
1
U9
1
Y1
1
Z1–Z3
3
UNPOPULATED COMPONENTS
1
DS9094F iButton
Clip
J18, J28–J30
1
J15
Not used
MAX1792EUA18 linear
regulator
DS2408 1-Wire 8-channel
addressable switch
Not used
U2
1
U10
1
U12
1
JUMPERS (DSTINIS400)
Network Boot Jumper (J3)
JUMPER
DS80C400 attempts to boot through
Ethernet using DHCP and TFTP
Quiet Boot Jumper (J5)
JUMPER
DS80C400 boots without sending loader
information to serial port.
Auto Negotiation Jumper (J9)
JUMPER
CONFIGURATION
1–2
Auto-negotiation disabled.
CONFIGURATION
1–2
CONFIGURATION
1–2
2–3
Auto-negotiation enabled.
iButton is a registered trademark of Dallas Semiconductor.
10/100Mb Ethernet Jumper (J10)
JUMPER
1–2
100Mb Ethernet operation.
2–3
10Mb Ethernet operation.
Full Duplex Jumper (J11)
JUMPER
Ethernet is configured for full-duplex
operation.
Ethernet is configured for half-duplex
operation.
DTR Reset Jumper (J11)
JUMPER
DTR reset is used for communication with
the DS80C400 loader application.
CONFIGURATION
CONFIGURATION
1–2
2–3
CONFIGURATION
1–2