參數資料
型號： DSPIC33FJ256MC510-I/PT
廠商： Microchip Technology
文件頁數： 117/136頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 256K 100TQFP
產品培訓模塊： dsPIC33F DMAC
Introduction to dsPIC33F Architecture Part 1
Asynchronous Stimulus
Introduction to dsPIC33F Architecture Part 2
特色產品： PIC24FJ/33FJ MCUs & dsPIC? DSCs
標準包裝： 119
系列： dsPIC™ 33F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 40 MIP
連通性： CAN，I²C，IrDA，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，DMA，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 85
程序存儲器容量： 256KB（256K x 8）
程序存儲器類型： 閃存
RAM 容量： 16K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 24x10b/12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-TQFP
包裝： 托盤
產品目錄頁面： 654 (CN2011-ZH PDF)
配用： 876-1001-ND - DSPIC33 BREAKOUT BOARD
MA330013-ND - MODULE PLUG-IN DSPIC33 100TQFP
DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
81
4235K–8051–05/08
AT89C51RD2/ED2
18.3
Power-Down Mode
The Power-Down mode places the AT89C51RD2/ED2 in a very low power state. Power-Down
mode stops the oscillator, freezes all clock at known states. The CPU status prior to entering
Power-Down mode is preserved, i.e., the program counter, program status word register retain
their data for the duration of Power-Down mode. In addition, the SFR and RAM contents are pre-
served. The status of the Port pins during Power-Down mode is detailed in Table 18-1.
Note:
VCC may be reduced to as low as VRET during Power-Down mode to further reduce power dissi-
pation. Take care, however, that VDD is not reduced until Power-Down mode is invoked.
18.3.1
Entering Power-Down Mode
To enter Power-Down mode, set PD bit in PCON register. The AT89C51RD2/ED2 enters the
Power-Down mode upon execution of the instruction that sets PD bit. The instruction that sets
PD bit is the last instruction executed.
18.3.2
Exiting Power-Down Mode
Note:
If VCC was reduced during the Power-Down mode, do not exit Power-Down mode until VCC is
restored to the normal operating level.
There are three ways to exit the Power-Down mode:
1.
Generate an enabled external interrupt.
– The AT89C51RD2/ED2 provides capability to exit from Power-Down using INT0#,
INT1#.
Hardware clears PD bit in PCON register which starts the oscillator and restores the
clocks to the CPU and peripherals. Using INTx# input, execution resumes when the
input is released (see Figure 18-1). Execution resumes with the interrupt service
routine. Upon completion of the interrupt service routine, program execution
resumes with the instruction immediately following the instruction that activated
Power-Down mode.
Note:
The external interrupt used to exit Power-Down mode must be configured as level sensitive
(INT0# and INT1#) and must be assigned the highest priority. In addition, the duration of the inter-
rupt must be long enough to allow the oscillator to stabilize. The execution will only resume when
the interrupt is deasserted.
Note:
Exit from power-down by external interrupt does not affect the SFRs nor the internal RAM content.
Figure 18-1. Power-Down Exit Waveform Using INT1:0#
2.
Generate a reset.
– A logic high on the RST pin clears PD bit in PCON register directly and
asynchronously. This starts the oscillator and restores the clock to the CPU and
peripherals. Program execution momentarily resumes with the instruction
immediately following the instruction that activated Power-Down mode and may
INT1:0#
OSC
Power-down phase
Oscillator restart phase
Active phase
相關PDF資料
PDF描述
PIC18F2585-I/SO IC MCU FLASH 24KX16 28SOIC
PIC16LC64A-04/L IC MCU OTP 2KX14 PWM 44PLCC
PIC16C73A-20/SO IC MCU OTP 4KX14 A/D PWM 28SOIC
PIC16C73A-10/SP IC MCU OTP 4KX14 A/D PWM 28DIP
PIC16C73A-20/SP IC MCU OTP 4KX14 A/D PWM 28DIP
相關代理商/技術參數
參數描述
dsPIC33FJ256MC510T-I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16 Bit MCU/DSP 40MIPS 256KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC510T-I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16 Bit MCU/DSP 40MIPS 256KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC710A-E/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16Bit 40MIPS 256KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC710A-E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16Bit 40MIPS 256KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC710A-H/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU 40MIPS 256KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*