參數資料
型號： DSPIC33FJ256MC510-I/PF
廠商： Microchip Technology
文件頁數： 116/136頁
文件大?。?/td> 0K
描述： IC DSPIC MCU/DSP 256K 100TQFP
產品培訓模塊： dsPIC33F DMAC
Introduction to dsPIC33F Architecture Part 1
Asynchronous Stimulus
Introduction to dsPIC33F Architecture Part 2
特色產品： PIC24FJ/33FJ MCUs & dsPIC? DSCs
標準包裝： 90
系列： dsPIC™ 33F
核心處理器： dsPIC
芯體尺寸： 16-位
速度： 40 MIP
連通性： CAN，I²C，IrDA，LIN，SPI，UART/USART
外圍設備： 欠壓檢測/復位，DMA，電機控制 PWM，QEI，POR，PWM，WDT
輸入/輸出數： 85
程序存儲器容量： 256KB（256K x 8）
程序存儲器類型： 閃存
RAM 容量： 16K x 8
電壓 - 電源 (Vcc/Vdd)： 3 V ~ 3.6 V
數據轉換器： A/D 24x10b/12b
振蕩器型： 內部
工作溫度： -40°C ~ 85°C
封裝/外殼： 100-TQFP
包裝： 托盤
產品目錄頁面： 654 (CN2011-ZH PDF)
配用： MA330013-ND - MODULE PLUG-IN DSPIC33 100TQFP
DV164033-ND - KIT START EXPLORER 16 MPLAB ICD2
DM240001-ND - BOARD DEMO PIC24/DSPIC33/PIC32
AC164323-ND - MODULE SKT FOR 100TQFP
80
4235K–8051–05/08
AT89C51RD2/ED2
18. Power Management
18.1
Introduction
Two power reduction modes are implemented in the AT89C51RD2/ED2. The Idle mode and the
Power-Down mode. These modes are detailed in the following sections. In addition to these
power reduction modes, the clocks of the core and peripherals can be dynamically divided by 2
using the X2 mode detailed in Section “Enhanced Features”, page 17.
18.2
Idle Mode
Idle mode is a power reduction mode that reduces the power consumption. In this mode, pro-
gram execution halts. Idle mode freezes the clock to the CPU at known states while the
peripherals continue to be clocked. The CPU status before entering Idle mode is preserved, i.e.,
the program counter and program status word register retain their data for the duration of Idle
mode. The contents of the SFRs and RAM are also retained. The status of the Port pins during
Idle mode is detailed in Table 18-1.
18.2.1
Entering Idle Mode
To enter Idle mode, set the IDL bit in PCON register (see Table 18-2). The AT89C51RD2/ED2
enters Idle mode upon execution of the instruction that sets IDL bit. The instruction that sets IDL
bit is the last instruction executed.
Note:
If IDL bit and PD bit are set simultaneously, the AT89C51RD2/ED2 enters Power-Down mode.
Then it does not go in Idle mode when exiting Power-Down mode.
18.2.2
Exiting Idle Mode
There are two ways to exit Idle mode:
1.
Generate an enabled interrupt.
– Hardware clears IDL bit in PCON register which restores the clock to the CPU.
Execution resumes with the interrupt service routine. Upon completion of the
interrupt service routine, program execution resumes with the instruction
immediately following the instruction that activated Idle mode. The general purpose
flags (GF1 and GF0 in PCON register) may be used to indicate whether an interrupt
occurred during normal operation or during Idle mode. When Idle mode is exited by
an interrupt, the interrupt service routine may examine GF1 and GF0.
2.
Generate a reset.
– A logic high on the RST pin clears IDL bit in PCON register directly and
asynchronously. This restores the clock to the CPU. Program execution momentarily
resumes with the instruction immediately following the instruction that activated the
Idle mode and may continue for a number of clock cycles before the internal reset
algorithm takes control. Reset initializes the AT89C51RD2/ED2 and vectors the CPU
to address C:0000h.
Note:
During the time that execution resumes, the internal RAM cannot be accessed; however, it is pos-
sible for the Port pins to be accessed. To avoid unexpected outputs at the Port pins, the instruction
immediately following the instruction that activated Idle mode should not write to a Port pin or to
the external RAM.
相關PDF資料
PDF描述
DSPIC33FJ256MC710-I/PF IC DSPIC MCU/DSP 256K 100TQFP
DSPIC33FJ32MC202-E/MM IC DSPIC MCU/DSP 32K 28QFN
DSPIC33FJ64MC710-I/PF IC DSPIC MCU/DSP 64K 100TQFP
EFM32G200F64 MCU 32BIT 64KB FLASH 32-QFN
EFM32G210F128 IC MCU 32BIT 128KB FLASH 32QFN
相關代理商/技術參數
參數描述
dsPIC33FJ256MC510T-I/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16 Bit MCU/DSP 40MIPS 256KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC510T-I/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16 Bit MCU/DSP 40MIPS 256KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC710A-E/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16Bit 40MIPS 256KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC710A-E/PT 功能描述:數字信號處理器和控制器 - DSP, DSC 16Bit 40MIPS 256KB Flash RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
dsPIC33FJ256MC710A-H/PF 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU 40MIPS 256KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*