- 您現在的位置：買賣IC網 > PDF目錄3823 > DSPIC30F4013-20I/ML (Microchip Technology)IC DSPIC MCU/DSP 48K 44QFN PDF資料下載
參數資料
| 型號： | DSPIC30F4013-20I/ML |
| 廠商： | Microchip Technology |
| 文件頁數： | 28/153頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DSPIC MCU/DSP 48K 44QFN |
| 產品培訓模塊： | Serial Communications using dsPIC30F CAN Serial Communications using dsPIC30F I2C Serial Communications using dsPIC30F SPI Serial Communications using dsPIC30F UART dsPIC30F 12 bit ADC - Part 2 dsPIC30F Addressing Modes - Part 1 dsPIC30F Architecture - Part 1 dsPIC30F DSP Engine & ALU dsPIC30F Interrupts dsPIC30F Motor Control PWM dsPIC Timers Asynchronous Stimulus dsPIC30F Addressing Modes - Part 2 dsPIC30F Architecture - Part 2 dsPIC30F 12-bit ADC Part 1 |
| 標準包裝： | 45 |
| 系列： | dsPIC™ 30F |
| 核心處理器： | dsPIC |
| 芯體尺寸： | 16-位 |
| 速度： | 20 MIPS |
| 連通性： | CAN，I²C，SPI，UART/USART |
| 外圍設備： | AC'97，欠壓檢測/復位，I²S，POR，PWM，WDT |
| 輸入/輸出數： | 30 |
| 程序存儲器容量： | 48KB（16K x 24） |
| 程序存儲器類型： | 閃存 |
| EEPROM 大?。?/td> | 1K x 8 |
| RAM 容量： | 2K x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 2.5 V ~ 5.5 V |
| 數據轉換器： | A/D 13x12b |
| 振蕩器型： | 內部 |
| 工作溫度： | -40°C ~ 85°C |
| 封裝/外殼： | 44-VQFN 裸露焊盤 |
| 包裝： | 管件 |
| 配用： | XLT44QFN2-ND - SOCKET TRAN ICE 44QFN/40DIP AC164322-ND - MODULE SOCKET MPLAB PM3 28/44QFN |
| 其它名稱： | DSPIC30F401320IML |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁當前第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁第71頁第72頁第73頁第74頁第75頁第76頁第77頁第78頁第79頁第80頁第81頁第82頁第83頁第84頁第85頁第86頁第87頁第88頁第89頁第90頁第91頁第92頁第93頁第94頁第95頁第96頁第97頁第98頁第99頁第100頁第101頁第102頁第103頁第104頁第105頁第106頁第107頁第108頁第109頁第110頁第111頁第112頁第113頁第114頁第115頁第116頁第117頁第118頁第119頁第120頁第121頁第122頁第123頁第124頁第125頁第126頁第127頁第128頁第129頁第130頁第131頁第132頁第133頁第134頁第135頁第136頁第137頁第138頁第139頁第140頁第141頁第142頁第143頁第144頁第145頁第146頁第147頁第148頁第149頁第150頁第151頁第152頁第153頁
2010 Microchip Technology Inc.
DS70138G-page 123
dsPIC30F3014/4013
18.3
DCI Module Operation
18.3.1
MODULE ENABLE
The DCI module is enabled or disabled by setting/
clearing the DCIEN control bit in the DCICON1 SFR.
Clearing the DCIEN control bit has the effect of reset-
ting the module. In particular, all counters associated
with CSCK generation, Frame Sync, and the DCI buffer
control unit are reset.
The DCI clocks are shut down when the DCIEN bit is
cleared.
When enabled, the DCI controls the data direction for
the four I/O pins associated with the module. The port,
LAT and TRIS register values for these I/O pins are
overridden by the DCI module when the DCIEN bit is set.
It is also possible to override the CSCK pin separately
when the bit clock generator is enabled. This permits
the bit clock generator to operate without enabling the
rest of the DCI module.
18.3.2
WORD-SIZE SELECTION BITS
The WS<3:0> word-size selection bits in the DCICON2
SFR determine the number of bits in each DCI data
word. Essentially, the WS<3:0> bits determine the
counting period for a 4-bit counter clocked from the
CSCK signal.
Any data length, up to 16 bits, may be selected. The
value loaded into the WS<3:0> bits is one less the
desired word length. For example, a 16-bit data word
size is selected when WS<3:0> = 1111.
18.3.3
FRAME SYNC GENERATOR
The Frame Sync generator (COFSG) is a 4-bit counter
that sets the frame length in data words. The Frame
Sync generator is incremented each time the word-size
counter is reset (refer to Section 18.3.2 “Word-Size
Selection Bits”). The period for the Frame Synchroni-
zation generator is set by writing the COFSG<3:0>
control bits in the DCICON2 SFR. The COFSG period
in clock cycles is determined by the following formula:
EQUATION 18-1:
COFSG PERIOD
Frame lengths, up to 16 data words, may be selected.
The frame length in CSCK periods can vary up to a
maximum of 256 depending on the word size that is
selected.
18.3.4
FRAME SYNC MODE
CONTROL BITS
The type of Frame Sync signal is selected using the
Frame
Synchronization
mode
control
bits
(COFSM<1:0>) in the DCICON1 SFR. The following
operating modes can be selected:
Multichannel mode
I2S mode
AC-Link mode (16-bit)
AC-Link mode (20-bit)
The operation of the COFSM control bits depends on
whether the DCI module generates the Frame Sync
signal as a master device, or receives the Frame Sync
signal as a slave device.
The master device in a DSP/Codec pair is the device
that generates the Frame Sync signal. The Frame Sync
signal initiates data transfers on the CSDI and CSDO
pins and usually has the same frequency as the data
sample rate (COFS).
The DCI module is a Frame Sync master if the COFSD
control bit is cleared and is a Frame Sync slave if the
COFSD control bit is set.
18.3.5
MASTER FRAME SYNC
OPERATION
When the DCI module is operating as a Frame Sync
master device (COFSD = 0), the COFSM mode bits
determine the type of Frame Sync pulse that is
generated by the Frame Sync generator logic.
A new COFS signal is generated when the Frame Sync
generator resets to ‘0’.
In the Multichannel mode, the Frame Sync pulse is
driven high for the CSCK period to initiate a data trans-
fer. The number of CSCK cycles between successive
Frame Sync pulses depends on the word size and
Frame Sync generator control bits. A timing diagram for
the Frame Sync signal in Multichannel mode is shown
in Figure 18-2.
In the AC-Link mode of operation, the Frame Sync
signal has a fixed period and duty cycle. The AC-Link
Frame Sync signal is high for 16 CSCK cycles and is
low for 240 CSCK cycles. A timing diagram with the
timing details at the start of an AC-Link frame is shown
in Figure 18-3.
In the I2S mode, a Frame Sync signal having a 50%
duty cycle is generated. The period of the I2S Frame
Sync signal in CSCK cycles is determined by the word
Note:
These WS<3:0> control bits are used only
in the Multichannel and I2S modes. These
bits have no effect in AC-Link mode since
the data slot sizes are fixed by the protocol.
Frame Length = Word Length (FSG Value + 1)
Note:
The COFSG control bits have no effect in
AC-Link mode since the frame length is
set to 256 CSCK periods by the protocol.
相關PDF資料 |
PDF描述 |
|---|---|
| DSPIC33FJ128GP804-I/ML | IC DSPIC MCU/DSP 128K 44QFN |
| PIC24HJ256GP206A-I/PT | IC MCU 16BIT 256KB FLASH 64TQFP |
| PIC16LF877A-I/P | IC MCU FLASH 8KX14 EE A/D 40DIP |
| PIC16F84-10I/P | IC MCU FLASH 1KX14 EE 18DIP |
| DSPIC30F4013-20I/P | IC DSPIC MCU/DSP 48K 40DIP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPIC30F4013-30I/ML | 功能描述:數字信號處理器和控制器 - DSP, DSC General Purpose RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F4013-30I/P | 功能描述:數字信號處理器和控制器 - DSP, DSC General Purpose RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F4013-30I/P | 制造商:Microchip Technology Inc 功能描述:16BIT MCU-DSP 30MHZ 30F4013 DIP40 |
| DSPIC30F4013-30I/PT | 功能描述:數字信號處理器和控制器 - DSP, DSC General Purpose RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPIC30F4013-30I/PT | 制造商:Microchip Technology Inc 功能描述:DIGITAL SIGNAL CONTROLLER 16 BIT ((NW)) |
發(fā)布緊急采購，3分鐘左右您將得到回復。