參數資料
型號： DSPIC30F2010
英文描述： dsPIC?Language Tools Getting Started
中文描述： dsPIC數字信號？語言工具入門
文件頁數： 36/56頁
文件大?。?/td> 2612K
代理商： DSPIC30F2010
dsPIC Language Tools Getting Started
DS70094B-page 32
2003 Microchip Technology Inc.
The other template code in this tutorial can be left in or commented out. It is probably
better to comment it out at this time since these definitions will get compiled and take
up memory space. Make sure to comment out all the sample arrays, since they use the
macros which can be commented out. Also, as the code grows, it may be difficult to
remember which code is used by the application and which was part of the original
template.
After the section labelled
END OF GLOBAL DEFINITIONS
type in this routine to
initialize Timer 1 as an interrupt timer using the internal clock (the bolded text is the
code that should be typed in):
EXAMPLE 3-4:
RESET_CLOCK CODE
This routine uses special function register names, such as
TMR1
and
T1CONbits.TCS
that are defined in the header file
p30F6014.h
. Refer to the data sheet for more
information on these control bits and registers for Timer 1.
Note:
When using the template, remember that when beginning to code the
application, only a few elements of the template may be needed. It may be
helpful to comment out those portions of code that are not being used so
that later, when similar elements are needed, they can be referred back to
as models.
/************** END OF GLOBAL DEFINITIONS ***********/
void reset_clock(void)
{
RTclock.timer = 0;
RTclock.ticks = 0;
RTclock.seconds = 0;
TMR1 = 0;
PR1 = TMR1_PERIOD;
T1CONbits.TCS = 0;
IPC0bits.T1IP = 4;
IFS0bits.T1IF = 0;
IEC0bits.T1IE = 1;
SRbits.IPL = 3;
T1CONbits.TON = 1;
}
/* clear software registers */
/* clear timer1 register */
/* set period1 register */
/* set internal clock source */
/* set priority level */
/* clear interrupt flag */
/* enable interrupts */
/* enable CPU priority levels 4-7 */
/* start the timer */
/************* START OF MAIN FUNCTION ***************/
相關PDF資料
PDF描述
DSR180-12-14 Single output 30W~180W
DSR180-48-24 Single output 30W~180W
DSR30-12-24 Single output 30W~180W
DSR30-12-48 Single output 30W~180W
DSR30-15-24 Single output 30W~180W
相關代理商/技術參數
參數描述
DSPIC30F2010 DEVELOPMENT BOARD KIT 功能描述:BOARD DEV FOR DSPIC30F2010 RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
DSPIC30F2010 DEVELOPMENT KIT 功能描述:KIT DEV EMBEDDED C RoHS:否 類別:編程器，開發系統 >> 通用嵌入式開發板和套件（MCU、DSP、FPGA、CPLD等） 系列:- 標準包裝:1 系列:PICDEM™ 類型:MCU 適用于相關產品:PIC10F206，PIC16F690，PIC16F819 所含物品:板，線纜，元件，CD，PICkit 編程器 產品目錄頁面:659 (CN2011-ZH PDF)
DSPIC30F2010_08 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:High-Performance, 16-bit Digital Signal Controllers
DSPIC30F2010_11 制造商:MICROCHIP 制造商全稱:Microchip Technology 功能描述:16-bit Digital Signal Controllers
dsPIC30F2010-20E/MM 功能描述:數字信號處理器和控制器 - DSP, DSC 16B MCU DSP 28LD 30MIPS 12KB FLASH RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*