- 您現在的位置：買賣IC網 > PDF目錄377002 > DSPCOMMPARALLELUM Parallel Port Command Converter for DSP User＇s Manual PDF資料下載
參數資料
| 型號： | DSPCOMMPARALLELUM |
| 英文描述： | Parallel Port Command Converter for DSP User＇s Manual |
| 中文描述： | 并行端口命令轉換為數字信號處理器用戶手冊 |
| 文件頁數： | 38/70頁 |
| 文件大?。?/td> | 550K |
| 代理商： | DSPCOMMPARALLELUM |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁當前第38頁第39頁第40頁第41頁第42頁第43頁第44頁第45頁第46頁第47頁第48頁第49頁第50頁第51頁第52頁第53頁第54頁第55頁第56頁第57頁第58頁第59頁第60頁第61頁第62頁第63頁第64頁第65頁第66頁第67頁第68頁第69頁第70頁
3-6
Universal Command Converter
Motorola
Host Computer Hardware
There are three input control bits in the middle-order byte of Port B data word that
represent the HOST_ACK, HOST_REQ, and INT_ACK. These signals are sent from the
host computer for reading and writing data. INT_ACK informs the monitor program that
the host computer has received its service request and is ready to communicate.
HOST_BRK is a wired-OR control line. HOST_BRK is used by the command converter
to inform the host computer whenever the target DSP has entered the Debug mode of
operation for non-JTAG devices only. Since more than one command converter may be
started for a user debug session, more than one may hold HOST_BRK active low at one
time. Once this signal is asserted it may only be deasserted by the host computer or by a
command converter reset.
3.1.5 Command Converter Interface Connector
The target application board must have a 14-pin connector to interface to the command
converter controller. This interface comprises nine signals and three ground connections
on a 7-row
×
2-column male pin header, which are spaced on 1/10 inch centers as
illustrated in Figure 3-4 on page 3-7.
Since the target system will have a resident reset circuit, it is recommended to have an
AND gate in series with the CC_RESET signal. This will insure that the target DSP will
be reset with a valid V
OL
level from either the target reset circuit or from the command
converter. The pull-down resistors are to insure that no false signals are propagated to the
JTAG/OnCE circuit when the test data input/debug serial input (TDI/DSI) and test data
clock/debug serial clock (TCK/DSCK) lines are active. The test data out/debug serial
output (TDO/DSO) pullup is to insure that the Debug Acknowledge signal from the OnCE
circuit is deasserted. The debug request (DR) pullup is to insure that the command
converter controls when the target DSP is placed into its Debug mode.
相關PDF資料 |
PDF描述 |
|---|---|
| DSPCOMMPCIUM | PCI Command Converter for DSP User＇s Manual |
| DSPG4001-71 | Telecommunication IC |
| DSPG5002 | Analog IC |
| DSPG5003 | Analog IC |
| DSPG5003-11 | Cell-Phone Circuit |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DSPCOMMPCIUM | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:PCI Command Converter for DSP User＇s Manual |
| DSPD374DB1 | 制造商:Freescale Semiconductor 功能描述:"D" ROM DAUGHTER CARD - Boxed Product (Development Kits) |
| DSPD56367AG150 | 功能描述:數字信號處理器和控制器 - DSP, DSC RoHS:否 制造商:Microchip Technology 核心:dsPIC 數據總線寬度:16 bit 程序存儲器大小:16 KB 數據 RAM 大小:2 KB 最大時鐘頻率:40 MHz 可編程輸入/輸出端數量:35 定時器數量:3 設備每秒兆指令數:50 MIPs 工作電源電壓:3.3 V 最大工作溫度:+ 85 C 封裝 / 箱體:TQFP-44 安裝風格:SMD/SMT |
| DSPD56371AF180 | 制造商:Freescale Semiconductor 功能描述: 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 181MHZ 181MIPS 80-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:AUDIO DSP |
| DSPD56374AE | 制造商:Freescale Semiconductor 功能描述:DSP FIXED-POINT 24-BIT 150MHZ 150MIPS 52-PIN LQFP TRAY - Trays 制造商:Freescale Semiconductor 功能描述:56374 52LQFP ROM D 0-70 |
發布緊急采購，3分鐘左右您將得到回復。