- 您現在的位置：買賣IC網 > PDF目錄376981 > DS80C320 (Maxim Integrated Products, Inc.) High-Speed/Low-Power Microcontrollers PDF資料下載
參數資料
| 型號： | DS80C320 |
| 廠商： | Maxim Integrated Products, Inc. |
| 英文描述： | High-Speed/Low-Power Microcontrollers |
| 中文描述： | 高速/低功耗微控制器 |
| 文件頁數： | 7/42頁 |
| 文件大?。?/td> | 1501K |
| 代理商： | DS80C320 |
第1頁第2頁第3頁第4頁第5頁第6頁當前第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁第39頁第40頁第41頁第42頁
DS80C320/DS80C323
7 of 42
HIGH-SPEED OPERATION
The DS80C320/DS80C323 is built around a high speed 80C32 compatible core. Higher speed comes not
just from increasing the clock frequency, but from a newer, more efficient design.
In this updated core, dummy memory cycles have been eliminated. In a conventional 80C32, machine
cycles are generated by dividing the clock frequency by 12. In the DS80C320/DS80C323, the same
machine cycle is performed in 4 clocks. Thus the fastest instruction, one machine cycle, is executed three
times faster for the same crystal frequency. Note that these are identical instructions. A comparison of the
timing differences is shown in Figure 2. The majority of instructions will see the full 3 to 1 speed
improvement. Some instructions will get between 1.5 and 2.4 X improvement. Note that all instructions
are faster than the original 80C51. Table 2 below shows a summary of the instruction set including the
speed.
The numerical average of all opcodes is approximately a 2.5 to 1 speed improvement. Individual
programs will be affected differently, depending on the actual instructions used. Speed-sensitive
applications would make the most use of instructions that are three times faster. However, the sheer
number of 3 to 1 improved opcodes makes dramatic speed improvements likely for any code. The Dual
Data Pointer feature also allows the user to eliminate wasted instructions when moving blocks of
memory.
INSTRUCTION SET SUMMARY
All instructions in the DS80C320/DS80C323 perform the same functions as their 80C32 counterparts.
Their effect on bits, flags, and other status functions is identical. However, the timing of each instruction
is different. This applies both in absolute and relative number of clocks.
For absolute timing of real-time events, the timing of software loops will need to be calculated using the
table below. However, counter/timers default to run at the older 12 clocks per increment. Therefore, while
software runs at higher speed, timer-based events need no modification to operate as before. Timers can
be set to run at 4 clocks per increment cycle to take advantage of higher speed operation.
The relative time of two instructions might be different in the new architecture than it was previously. For
example, in the original architecture, the “MOVX A, @DPTR” instruction and the “MOV direct, direct”
instruction used two machine cycles or 24 oscillator cycles. Therefore, they required the same amount of
time. In the DS80C320/DS80C323, the MOVX instruction can be done in two machine cycles or eight
oscillator cycles but the “MOV direct, direct” uses three machine cycles or 12 oscillator cycles. While
both are faster than their original counterparts, they now have different execution times from each other.
This is because in most cases, the DS80C320/DS80C323 uses one cycle for each byte. The user
concerned with precise program timing should examine the timing of each instruction for familiarity with
the changes. Note that a machine cycle now requires just four clocks, and provides one ALE pulse per
cycle. Many instructions require only one cycle, but some require five. In the original architecture, all
were one or two cycles except for MUL and DIV.
相關PDF資料 |
PDF描述 |
|---|---|
| DS80C320-ECG | Strain Relief |
| DS80C320-ECL | High-Speed/Low-Power Microcontrollers |
| DS80C320-ENG | High-Speed/Low-Power Microcontrollers |
| DS80C320-ENL | High-Speed/Low-Power Microcontrollers |
| DS80C320-MCG | High-Speed/Low-Power Microcontrollers |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C320_06 | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:High-Speed/Low-Power Microcontrollers |
| DS80C320+ENL | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 44TQFP - Trays |
| DS80C320+FCG | 制造商:Maxim Integrated Products 功能描述:MICRO HI SPD 44PQFP 25MHZ PB-FREE - Trays |
| DS80C320+FNG | 制造商:Maxim Integrated Products 功能描述:MICRO HS 44MQFP 25MHZ IND PB-FREE - Trays |
| DS80C320+MCG | 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 40PDIP - Rail/Tube 制造商:Maxim Integrated Products 功能描述:IC 8BIT CPU CMOS 80C320 DIP40 制造商:Maxim Integrated Products 功能描述:IC, 8BIT CPU CMOS, 80C320, DIP40 制造商:Maxim Integrated Products 功能描述:IC, 8BIT CPU CMOS, 80C320, DIP40; Controller Family/Series:(8051) 8052; Core Size:8bit; No. of I/O's:32; Supply Voltage Min:4.5V; Supply Voltage Max:5.5V; Digital IC Case Style:DIP; No. of Pins:40; RAM Memory Size:256Byte; CPU ;RoHS Compliant: Yes |
發布緊急采購，3分鐘左右您將得到回復。