參數資料
型號： DS80C320-QCL
英文描述： High-Speed/Low-Power Micro
中文描述： High-Speed/Low-Power微
文件頁數： 21/42頁
文件大?。?/td> 1501K
代理商： DS80C320-QCL
DS80C320/DS80C323
21 of 42
NOTES FOR DS80C320 DC ELECTRICAL CHARACTERISTICS:
All parameters apply to both commercial and industrial temperature operation unless otherwise noted.
1. All voltages are referenced to ground.
2. Active current is measured with a 25 MHz clock source driving XTAL1, V
CC
=RST=5.5V, all other
pins disconnected.
3. Idle mode current is measured with a 25 MHz clock source driving XTAL1, V
CC
=5.5V, RST at
ground, all other pins disconnected.
4. Stop mode current measured with XTAL1 and RST grounded, V
CC
=5.5V, all other pins disconnected.
when addressing external memory.
5. When addressing external memory.
6. RST=V
CC
. This condition mimics operation of pins in I/O mode.
7. During a 0 to 1 transition, a one-shot drives the ports hard for two clock cycles. This measurement
reflects port in transition mode.
8. Ports 1, 2, and 3 source transition current when being pulled down externally. It reaches its maximum
at approximately 2V.
9. 0.45<V
IN
<V
CC
. Not a high impedance input. This port is a weak address holding latch because Port 0
is dedicated as an address bus on the DS80C320. Peak current occurs near the input transition point of
the latch, approximately 2V.
10. Over the industrial temperature range, this specification has a maximum value of 200 μA.
11. This is the current required from an external circuit to hold a logic low level on an I/O pin while the
corresponding port latch bit is set to 1. This is only the current required to
hold
the low level;
transitions from 1 to 0 on an I/O pin will also have to overcome the transition current.
12. Device operating range is 4.5V to 5.5V; however, device is tested to 4.0V to ensure proper operation
at minimum V
RST
.
相關PDF資料
PDF描述
DS80C320 High-Speed/Low-Power Micro
DS80C320-ECG High-Speed/Low-Power Micro
DS80C320-ECL High-Speed/Low-Power Micro
DS80C320-ENG High-Speed/Low-Power Micro
DS80C320-QNL High-Speed/Low-Power Micro
相關代理商/技術參數
參數描述
DS80C320-QCL/T&R 制造商:Maxim Integrated Products 功能描述:MICRO, HI SPD, 44PLCC, 33MHZ, TRL - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MCU HI SPEED 33MHZ 44-PLCC 制造商:Maxim Integrated Products 功能描述:8-bit Microcontrollers - MCU High-Speed Low-Power
DS80C320-QCL/T&R 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C320-QCL+ 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS80C320-QCL+T&R 制造商:Maxim Integrated Products 功能描述:MCU 8BIT CISC ROMLESS 5V 44PLCC - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC MCU HI SPEED 33MHZ 44-PLCC 制造商:Maxim Integrated Products 功能描述:8-bit Microcontrollers - MCU High-Speed Low-Power
DS80C320-QCL+T&R 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*