- 您現在的位置：買賣IC網 > PDF目錄11790 > DS80C320-MCG+ (Maxim Integrated Products)IC MCU HI SPEED 25MHZ 40-DIP PDF資料下載
參數資料
| 型號： | DS80C320-MCG+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 6/38頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC MCU HI SPEED 25MHZ 40-DIP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 10 |
| 系列： | 80C |
| 核心處理器： | 8051 |
| 芯體尺寸： | 8-位 |
| 速度： | 25MHz |
| 連通性： | EBI/EMI，SIO，UART/USART |
| 外圍設備： | 電源故障復位，WDT |
| 輸入/輸出數： | 32 |
| 程序存儲器類型： | ROMless |
| RAM 容量： | 256 x 8 |
| 電壓 - 電源 (Vcc/Vdd)： | 4.5 V ~ 5.5 V |
| 振蕩器型： | 外部 |
| 工作溫度： | 0°C ~ 70°C |
| 封裝/外殼： | 40-DIP（0.600"，15.24mm） |
| 包裝： | 管件 |
| 產品目錄頁面： | 703 (CN2011-ZH PDF) |
第1頁第2頁第3頁第4頁第5頁當前第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁第28頁第29頁第30頁第31頁第32頁第33頁第34頁第35頁第36頁第37頁第38頁
DS80C320/DS80C323 High-Speed/Low-Power Microcontrollers
14 of 38
64-Byte Block Move with Dual Data Pointer
; SH and SL are high and low byte source address.
; DH and DL are high and low byte of destination address.
; DPS is the data pointer select. Reset condition is DPS=0, DPTR0 is selected.
# CYCLES
EQU
DPS, #86h
; TELL ASSEMBLER ABOUT DPS
MOV
R5, #64
; NUMBER OF BYTES TO MOVE
2
MOV
DPTR, #DHDL
; LOAD DESTINATION ADDRESS
3
INC
DPS
; CHANGE ACTIVE DPTR
2
MOV
DPTR, #SHSL
; LOAD SOURCE ADDRESS
2
MOVE:
; THIS LOOP IS PERFORMED THE NUMBER OF TIMES LOADED INTO R5, IN THIS EXAMPLE 64
MOVX
A, @DPTR
; READ SOURCE DATA BYTE
2
INC
DPS
; CHANGE DPTR TO DESTINATION
2
MOVX
@DPTR, A
; WRITE DATA TO DESTINATION
2
INC
DPTR
; NEXT DESTINATION ADDRESS
3
INC
DPS
; CHANGE DATA POINTER TO SOURCE
2
INC
DPTR
; NEXT SOURCE ADDRESS
3
DJNZ
R5, MOVE
; FINISHED WITH TABLE?
3
PERIPHERAL OVERVIEW
Peripherals in the DS80C320/DS80C323 are accessed using the SFRs. The devices provide several of the
most commonly needed peripheral functions in microcomputer-based systems. These functions are new
to the 80C32 family and include a second serial port, power-fail reset, power-fail interrupt, and a
programmable watchdog timer. These are briefly described in the following paragraphs. More details are
available in the High-Speed Microcontroller User’s Guide.
SERIAL PORTS
The DS80C320/DS80C323 provide a serial port (UART) that is identical to the 80C32. Many
applications require serial communication with multiple devices. Therefore, a second hardware serial port
is provided that is a full duplicate of the standard one. It optionally uses pins P1.2 (RXD1) and P1.3
(TXD1). This port has duplicate control functions included in new SFR locations. The second serial port
operates in a comparable manner with the first. Both can operate simultaneously but can be at different
baud rates.
The second serial port has similar control registers (SCON1 at C0h, SBUF1 at C1h) to the original. One
difference is that for timer-based baud rates, the original serial port can use Timer 1 or Timer 2 to
generate baud rates. This is selected via SFR bits. The new serial port can only use Timer 1.
TIMER-RATE CONTROL
One important difference exists between the DS80C320/DS80C323 and 80C32 regarding timers. The
original 80C32 used a 12 clock-per-cycle scheme for timers and consequently for some serial baud rates
(depending on the mode). The DS80C320/DS80C323 architecture normally runs using 4 clocks per cycle.
However, in the area of timers, it will default to a 12 clock-per-cycle scheme on a reset. This allows
existing code with real-time dependencies such as baud rates to operate properly. If an application needs
higher speed timers or serial baud rates, the timers can be set to run at the 4-clock rate.
The Clock Control register (CKCON - 8Eh) determines these timer speeds. When the relevant CKCON
bit is a logic 1, the device uses 4 clocks per cycle to generate timer speeds. When the control bit is set to a
0, the device uses 12 clocks for timer speeds. The reset condition is a 0. CKCON.5 selects the speed of
Timer 2. CKCON.4 selects Timer 1 and CKCON.3 selects Timer 0. Note that unless a user desires very
fast timing, it is unnecessary to alter these bits. Note that the timer controls are independent.
相關PDF資料 |
PDF描述 |
|---|---|
| V72B8H150B3 | CONVERTER MOD DC/DC 8V 150W |
| AT32UC3C1512C-AZR | IC MCU AVR32 512K FLASH 100LQFP |
| AT32UC3A0512-ALUR | MCU 32BIT 512KB FLASH 144-LQFP |
| V72B8H150B2 | CONVERTER MOD DC/DC 8V 150W |
| AT32UC3A3128-CTUR | IC MCU 128KB FLASH 144TBGA |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS80C320MCG+ | 制造商:Maxim Integrated Products 功能描述:DS80C320 8bit microcontroller,25MHz |
| DS80C320-MCG+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80C320-MCL | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS80C320MCL+ | 制造商:DSC 功能描述: |
| DS80C320-MCL+ | 功能描述:8位微控制器 -MCU High-Speed Low-Power RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
發布緊急采購，3分鐘左右您將得到回復。