- 您現在的位置：買賣IC網 > PDF目錄379184 > DS75 2.Wire Thermal Watchdog PDF資料下載
參數資料
| 型號： | DS75 |
| 英文描述： | 2.Wire Thermal Watchdog |
| 中文描述： | 數字溫度計和溫度監控器 |
| 文件頁數： | 8/13頁 |
| 文件大?。?/td> | 240K |
| 代理商： | DS75 |
DS75
8 of 13
2–WIRE SERIAL DATA BUS
The DS75 supports a bi–directional two–wire bus and data transmission protocol. A device that sends
data onto the bus is defined as a transmitter, and a device receiving data as a receiver. The device that
controls the message is called a “master”. The devices that are controlled by the master are “slaves”. The
bus must be controlled by a master device which generates the serial clock (SCL), controls the bus access,
and generates the START and STOP conditions. The DS75 operates as a slave on the two–wire bus.
Connections to the bus are made via the open–drain I/O lines SDA and SCL.
The following bus protocol has been defined (See Figure 4):
Data transfer may be initiated only when the bus is not busy.
During data transfer, the data line must remain stable whenever the clock line is HIGH. Changes in
the data line while the clock line is high will be interpreted as control signals.
Accordingly, the following bus conditions have been defined:
Bus not busy:
Both data and clock lines remain HIGH.
Start data transfer:
A change in the state of the data line, from HIGH to LOW, while the clock is
HIGH, defines a START condition.
Stop data transfer:
A change in the state of the data line, from LOW to HIGH, while the clock line is
HIGH, defines the STOP condition.
Data valid:
The state of the data line represents valid data when, after a START condition, the data line
is stable for the duration of the HIGH period of the clock signal. The data on the line must be changed
during the LOW period of the clock signal. There is one clock pulse per bit of data.
Each data transfer is initiated with a START condition and terminated with a STOP condition. The
number of data bytes transferred between START and STOP conditions is not limited, and is determined
by the master device. The information is transferred byte–wise and each receiver acknowledges with a
ninth bit.
Within the bus specifications a regular mode (100 kHz clock rate) and a fast mode (400 kHz clock rate)
are defined. The DS75 works in both modes.
Acknowledge:
Each receiving device, when addressed, is obliged to generate an acknowledge after
the reception of each byte. The master device must generate an extra clock pulse which is associated with
this acknowledge bit.
A device that acknowledges must pull down the SDA line during the acknowledge clock pulse in such a
way that the SDA line is stable LOW during the HIGH period of the acknowledge related clock pulse. Of
course, setup and hold times must be taken into account. A master must signal an end of data to the slave
by not generating an acknowledge bit on the last byte that has been clocked out of the slave. In this case,
the slave must leave the data line HIGH to enable the master to generate the STOP condition.
相關PDF資料 |
PDF描述 |
|---|---|
| DS75S | 2.Wire Thermal Watchdog |
| DS80CH11 | System Energy Manager |
| DS83C520 | EPROM/ROM High-Speed Micro |
| DS83C520-ECL | EPROM/ROM High-Speed Micro |
| DS83C520-ENL | EPROM/ROM High-Speed Micro |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS7505 | 制造商:Maxim Integrated Products 功能描述:LOW-VOLTAGE (1.7V TO 3.7V)DIGITAL THERMOMETER & THERMOSTAT - Rail/Tube |
| DS7505S | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Digital Thermometer and Thermostat |
| DS7505S+ | 功能描述:板上安裝溫度傳感器 Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
| DS7505S+T&R | 制造商:Maxim Integrated Products 功能描述:DGTL THERMOMETER AND THERMOSTAT 8SOIC N - Tape and Reel 制造商:Maxim Integrated Products 功能描述:IC DGTL THERMOMETER 2WIRE 8-SOIC |
| DS7505S+T&R | 功能描述:板上安裝溫度傳感器 Thermometer & Thermostat RoHS:否 制造商:Omron Electronics 輸出類型:Digital 配置: 準確性:+/- 1.5 C, +/- 3 C 溫度閾值: 數字輸出 - 總線接口:2-Wire, I2C, SMBus 電源電壓-最大:5.5 V 電源電壓-最小:4.5 V 最大工作溫度:+ 50 C 最小工作溫度:0 C 關閉: 安裝風格: 封裝 / 箱體: 設備功能:Temperature and Humidity Sensor |
發布緊急采購，3分鐘左右您將得到回復。