- 您現在的位置：買賣IC網 > PDF目錄97869 > DS5001FP-16 (MAXIM INTEGRATED PRODUCTS INC) 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 PDF資料下載
參數資料
| 型號： | DS5001FP-16 |
| 廠商： | MAXIM INTEGRATED PRODUCTS INC |
| 元件分類： | Microcontroller |
| 英文描述： | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
| 封裝： | MQFP-80 |
| 文件頁數： | 3/27頁 |
| 文件大?。?/td> | 934K |
| 代理商： | DS5001FP-16 |
第1頁第2頁當前第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁第13頁第14頁第15頁第16頁第17頁第18頁第19頁第20頁第21頁第22頁第23頁第24頁第25頁第26頁第27頁
DS5001FP
11 of 27
Figure 6. DS5001FP CONNECTION TO 64k x 8 SRAM
POWER MANAGEMENT
The DS5001FP monitors VCC to provide power-fail reset, early warning power-fail interrupt, and switch
over to lithium backup. It uses an internal bandgap reference in determining the switch points. These are
called VPFW, VCCMIN, and VLI, respectively. When VCC drops below VPFW, the DS5001FP performs an
interrupt vector to location 2Bh if the power-fail warning was enabled. Full processor operation continues
regardless. When power falls further to VCCMIN, the DS5001FP invokes a reset state. No further code
execution is performed unless power rises back above VCCMIN. All decoded chip enables and the R/ W
signal go to an inactive (logic 1) state. VCC is still the power source at this time. When VCC drops further
to below VLI, internal circuitry switches to the lithium cell for power. The majority of internal circuits are
disabled and the remaining nonvolatile states are retained. Any devices connected VCCO are powered by
the lithium cell at this time. VCCO is at the lithium battery voltage minus approximately 0.45V. This drop
varies depending on the load. Low power SRAMs should be used for this reason. When using the
DS5001FP, the user must select the appropriate battery to match the RAM data retention current and the
desired backup lifetime. Note that the lithium cell is only loaded when VCC < VLI. The User’s Guide has
more information on this topic. The trip points VCCMIN and VPFW are listed in the Electrical Specifications
section.
相關PDF資料 |
PDF描述 |
|---|---|
| DS5002FP-16 | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
| DS5002FPM-16 | 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80 |
| DS75S | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, RECTANGULAR, SURFACE MOUNT |
| DS75U/T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
| DS75U-C12+T&R | DIGITAL TEMP SENSOR-SERIAL, 12BIT(s), 2Cel, SQUARE, SURFACE MOUNT |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS5001FP-16+ | 功能描述:微處理器 - MPU Soft MCU Chip RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| DS5001FP-16N | 功能描述:微處理器 - MPU Soft MCU Chip RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| DS5001FP-16N+ | 功能描述:微處理器 - MPU Soft MCU Chip RoHS:否 制造商:Atmel 處理器系列:SAMA5D31 核心:ARM Cortex A5 數據總線寬度:32 bit 最大時鐘頻率:536 MHz 程序存儲器大小:32 KB 數據 RAM 大小:128 KB 接口類型:CAN, Ethernet, LIN, SPI,TWI, UART, USB 工作電源電壓:1.8 V to 3.3 V 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:FBGA-324 |
| DS5001FPN08 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
| DS5001FPN12 | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller |
發布緊急采購，3分鐘左右您將得到回復。