參數資料
型號： DS5000T-8-16
廠商： DALLAS SEMICONDUCTOR
元件分類： Microcontroller
英文描述： 8-BIT, 16 MHz, MICROCONTROLLER, DMA40
文件頁數： 13/19頁
文件大?。?/td> 301K
代理商： DS5000T-8-16
DS5000(T)
3 of 19
PIN DESCRIPTION
PIN
DESCRIPTION
1-8
P1.0 - P1.7. General purpose I/O Port 1.
9
RST - Active high reset input. A logic 1 applied to this pin will activate a reset state. This
pin is pulled down internally so this pin can be left unconnected if not used.
10
P3.0 RXD. General purpose I/O port pin 3.0. Also serves as the receive signal for the on
board UART. This pin should not be connected directly to a PC COM port.
11
P3.1 TXD. General purpose I/O port pin 3.1. Also serves as the transmit signal for the on
board UART. This pin should not be connected directly to a PC COM port.
12
P3.2 INT0 . General purpose I/O port pin 3.2. Also serves as the active low External
Interrupt 0.
13
P3.3 INT1 . General purpose I/O port pin 3.3. Also serves as the active low External
Interrupt 1.
14
P3.4 T0. General purpose I/O port pin 3.4. Also serves as the Timer 0 input.
15
P3.5 T1. General purpose I/O port pin 3.5. Also serves as the Timer 1 input.
16
P3.6 WR . General purpose I/O port pin. Also serves as the write strobe for Expanded bus
operation.
17
P3.7 RD . General purpose I/O port pin. Also serves as the read strobe for Expanded bus
operation.
18, 19
XTAL2, XTAL1. Used to connect an external crystal to the internal oscillator. XTAL1 is
the input to an inverting amplifier and XTAL2 is the output.
20
GND. Logic ground.
21-28
P2.0-P2.7. General purpose I/O Port 2. Also serves as the MSB of the Expanded Address
bus.
29
PSEN
- Program Store Enable. This active low signal is used to enable an external
program memory when using the Expanded bus. It is normally an output and should be
unconnected if not used. PSEN also is used to invoke the Bootstrap Loader. At this time,
PSEN
will be pulled down externally. This should only be done once the DS5000(T) is
already in a reset state. The device that pulls down should be open drain since it must not
interfere with PSEN under normal operation.
30
ALE - Address Latch Enable. Used to de-multiplex the multiplexed Expanded
Address/Data bus on Port 0. This pin is normally connected to the clock input on a ’373
type transparent latch. When using a parallel programmer, this pin also assumes the
PROG
function for programming pulses.
31
EA
- External Access. This pin forces the DS5000(T) to behave like an 8031. No internal
memory (or clock) will be available when this pin is at a logic low. Since this pin is pulled
down internally, it should be connected to +5V to use NV RAM. In a parallel
programmer, this pin also serves as VPP for super voltage pulses.
32-39
P0.7-P0.0. General purpose I/O Port 0. This port is open-drain and cannot drive a logic 1.
It requires external pullups. Port 0 is also the multiplexed Expanded Address/Data bus.
When used in this mode, it does not require pullups.
40
VCC - +5 volts.
相關PDF資料
PDF描述
DS5000T-8-8 8-BIT, 8 MHz, MICROCONTROLLER, PDIP40
DS5000T-8-12 8-BIT, 12 MHz, MICROCONTROLLER, PDIP40
DS5001FP-16 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80
DS5002FP-16 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80
DS5002FPM-16 8-BIT, 16 MHz, MICROCONTROLLER, PQFP80
相關代理商/技術參數
參數描述
DS5000T-8-8 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT
DS5000TK 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller Evaluation Kit
DS5001FP 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip
DS5001FP_05 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip
DS5001FP08 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller
發布緊急采購，3分鐘左右您將得到回復。

采購需求

(若只采購一條型號，填寫一行即可)

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

發布成功！您可以繼續發布采購。也可以進入我的后臺，查看報價

*型號 *數量 廠商 批號 封裝
添加更多采購

我的聯系方式

*
*
*