- 您現在的位置：買賣IC網 > PDF目錄376978 > DS5000T-32-8 Soft Microcontroller PDF資料下載
參數資料
| 型號： | DS5000T-32-8 |
| 英文描述： | Soft Microcontroller |
| 中文描述： | 軟微控制器 |
| 文件頁數： | 3/19頁 |
| 文件大?。?/td> | 131K |
| 代理商： | DS5000T-32-8 |
DS5000(T)
021998 3/19
PIN DESCRIPTION
PIN NUMBER
DESCRIPTION
1–8
P1.0 – P1.7.
General purpose I/O Port 1.
9
RST –
Active high reset input. A logic 1 applied to this pin will activate a reset state. This pin
is pulled down internally so this pin can be left unconnected if not used.
10
P3.0 RXD.
General purpose I/O port pin 3.0. Also serves as the receive signal for the on
board UART. This pin should not be connected directly to a PC COM port.
11
P3.1 TXD.
General purpose I/O port pin 3.1. Also serves as the transmit signal for the on
board UART. This pin should not be connected directly to a PC COM port.
12
P3.2 INT0.
General purpose I/O port pin 3.2. Also serves as the active low External
Interrupt 0.
13
P3.3 INT1.
General purpose I/O port pin 3.3. Also serves as the active low External
Interrupt 1.
14
P3.4 T0.
General purpose I/O port pin 3.4. Also serves as the Timer 0 input.
15
P3.5 T1.
General purpose I/O port pin 3.5. Also serves as the Timer 1 input.
16
P3.6 WR.
General purpose I/O port pin. Also serves as the write strobe for Expanded
bus operation.
17
P3.7 RD.
General purpose I/O port pin. Also serves as the read strobe for Expanded bus
operation.
18, 19
XTAL2, XTAL1.
Used to connect an external crystal to the internal oscillator. XTAL1 is the
input to an inverting amplifier and XTAL2 is the output.
20
GND.
Logic ground.
21–28
P2.0–P2.7.
General purpose I/O Port 2. Also serves as the MSB of the Expanded Address
bus.
29
PSEN –
Program Store Enable. This active low signal is used to enable an external program
memory when using the Expanded bus. It is normally an output and should be unconnected
if not used. PSEN also is used to invoke the Bootstrap Loader. At this time, PSEN will be
pulled down externally. This should only be done once the DS5000(T) is already in a reset
state. The device that pulls down should be open drain since it must not interfere with PSEN
under normal operation.
30
ALE
–
Address Latch Enable. Used to de–multiplex the multiplexed Expanded Address/Data
bus on Port 0. This pin is normally connected to the clock input on a ’373 type transparent
latch. When using a parallel programmer, this pin also assumes the PROG function for pro-
gramming pulses.
31
EA –
External Access. This pin forces the DS5000(T) to behave like an 8031. No internal
memory (or clock) will be available when this pin is at a logic low. Since this pin is pulled down
internally, it should be connected to +5V to use NV RAM. In a parallel programmer, this pin
also serves as V
PP
for super voltage pulses.
相關PDF資料 |
PDF描述 |
|---|---|
| DS5001FP | 128k Soft Microprocessor Chip |
| DS5001FP-12-44 | TRIMMER, 4 TURN 100R |
| DS5001FP-16 | 128k Soft Microprocessor Chip |
| DS5001FP-16N | 128k Soft Microprocessor Chip |
| DS5002FMN-16 | Secure Microprocessor Chip |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS5000T-8-12 | 制造商:Rochester Electronics LLC 功能描述: 制造商:Maxim Integrated Products 功能描述: |
| DS5000T-8-16 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS5000T-8-8 | 功能描述:8位微控制器 -MCU RoHS:否 制造商:Silicon Labs 核心:8051 處理器系列:C8051F39x 數據總線寬度:8 bit 最大時鐘頻率:50 MHz 程序存儲器大小:16 KB 數據 RAM 大小:1 KB 片上 ADC:Yes 工作電源電壓:1.8 V to 3.6 V 工作溫度范圍:- 40 C to + 105 C 封裝 / 箱體:QFN-20 安裝風格:SMD/SMT |
| DS5000TK | 制造商:未知廠家 制造商全稱:未知廠家 功能描述:Microcontroller Evaluation Kit |
| DS5001FP | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:128k Soft Microprocessor Chip |
發布緊急采購，3分鐘左右您將得到回復。