- 您現在的位置：買賣IC網 > PDF目錄8542 > DS4412U+T&R (Maxim Integrated Products)IC DAC DUAL CH I2C ADJ 8-USOP PDF資料下載
參數資料
| 型號： | DS4412U+T&R |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 8/10頁 |
| 文件大?。?/td> | 0K |
| 描述： | IC DAC DUAL CH I2C ADJ 8-USOP |
| 產品培訓模塊： | Lead (SnPb) Finish for COTS Obsolescence Mitigation Program |
| 標準包裝： | 3,000 |
| 位數： | 4 |
| 數據接口： | I²C |
| 轉換器數目： | 2 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 8-TSSOP，8-MSOP（0.118"，3.00mm 寬） |
| 供應商設備封裝： | 8-uMAX |
| 包裝： | 帶卷 (TR) |
| 輸出數目和類型： | 2 電流，單極 |
| 采樣率（每秒）： | * |
SCL
NOTE: TIMING IS REFERENCED TO VIL(MAX) AND VIH(MIN).
SDA
STOP
START
REPEATED
START
tBUF
tHD:STA
tHD:DAT
tSU:DAT
tSU:STO
tHD:STA
tSP
tSU:STA
tHIGH
tR
tF
tLOW
Figure 1. I2C Timing Diagram
I2C Serial Interface Description
I2C Slave Address
The DS4412’s slave address is 90h.
I2C Definitions
The following terminology is commonly used to describe
I2C data transfers:
Master Device: The master device controls the slave
devices on the bus. The master device generates
SCL clock pulses and START and STOP conditions.
Slave Devices: Slave devices send and receive
data at the master’s request.
Bus Idle or Not Busy: Time between STOP and
START conditions when both SDA and SCL are inac-
tive and in their logic-high states. When the bus is
idle it often initiates a low-power mode for slave
devices.
START Condition: A START condition is generated
by the master to initiate a new data transfer with a
slave. Transitioning SDA from high to low while SCL
remains high generates a START condition. See
Figure 1 for applicable timing.
STOP Condition: A STOP condition is generated by
the master to end a data transfer with a slave.
Transitioning SDA from low to high while SCL
remains high generates a STOP condition. See
Figure 1 for applicable timing.
Repeated START Condition: The master can use a
repeated START condition at the end of one data
transfer to indicate that it will immediately initiate a
new data transfer following the current one. Repeated
starts are commonly used during read operations to
identify a specific memory address to begin a data
transfer. A repeated START condition is issued identi-
cally to a normal START condition. See Figure 1 for
applicable timing.
Bit Write: Transitions of SDA must occur during the
low state of SCL. The data on SDA must remain valid
and unchanged during the entire high pulse of SCL,
plus the setup and hold time requirements (Figure 1).
Data is shifted into the device during the rising edge
of the SCL.
Bit Read: At the end of a write operation, the master
must release the SDA bus line for the proper amount
of setup time (Figure 1) before the next rising edge of
SCL during a bit read. The device shifts out each bit of
data on SDA at the falling edge of the previous SCL
pulse and the data bit is valid at the rising edge of the
current SCL pulse. Remember that the master gener-
ates all SCL clock pulses, including when it is reading
bits from the slave.
Acknowledgement (ACK and NACK): An
Acknowledgement (ACK) or Not Acknowledge
(NACK) is always the ninth bit transmitted during a
byte transfer. The device receiving data (the master
during a read or the slave during a write operation)
performs an ACK by transmitting a zero during the
ninth bit. A device performs a NACK by transmitting
a one during the ninth bit. Timing for the ACK and
NACK is identical to all other bit writes (Figure 2). An
ACK is the acknowledgment that the device is prop-
erly receiving data. A NACK is used to terminate a
DS4412
Dual-Channel, I2C Adjustable
Sink/Source Current DAC
_______________________________________________________________________________________
7
相關PDF資料 |
PDF描述 |
|---|---|
| VE-BVL-MX-S | CONVERTER MOD DC/DC 28V 75W |
| VE-BVK-MX-S | CONVERTER MOD DC/DC 40V 75W |
| VE-J5N-MW-S | CONVERTER MOD DC/DC 18.5V 100W |
| HI5731BIPZ | IC DAC 12BIT 100MSPS HS 28DIP |
| HI5741BIBZ-T | CONV D/A 14BIT 100MSPS 28SOIC |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS441405-BA | 功能描述:CAP FILM 4UF 440VAC QC TERM RoHS:是 類別:電容器 >> 薄膜 系列:PMF 特色產品:ECW-H(C) Series Film Capacitors 標準包裝:100 系列:ECW-H(C) 電容:0.33µF 額定電壓 - AC:- 額定電壓 - DC:630V 電介質材料:聚丙烯，金屬化 容差:±3% ESR（等效串聯電阻）:- 工作溫度:-40°C ~ 105°C 安裝類型:通孔 封裝/外殼:徑向 尺寸/尺寸:0.815" L x 0.579" W（20.70mm x 14.70mm） 高度 - 座高（最大）:1.028"（26.10mm） 端子:PC 引腳 引線間隔:0.394"（10.00mm） 特點:高頻和高穩定性 應用:- 包裝:散裝 其它名稱:ECWH6334HCBP15432 |
| DS4414FP00K | 制造商:Thomas & Betts 功能描述:400A,CON,3P4W,MG,414,3P600V,CC |
| DS4414FR000 | 制造商:Thomas & Betts 功能描述:400A,REC,3P4W,MG,414,3P600V |
| DS4414FRABK | 制造商:Thomas & Betts 功能描述:400A,REC,3P4W,MG,414,ABK,3P600V |
| DS4414MP000 | 制造商:Thomas & Betts 功能描述:400A,PLG,3P4W,MG,414,3P600V |
發布緊急采購，3分鐘左右您將得到回復。