參數資料
| 型號： | DS4404N+ |
| 廠商： | Maxim Integrated Products |
| 文件頁數： | 5/9頁 |
| 文件大小： | 0K |
| 描述： | IC DAC 4CH I2C ADJ 14-TDFN |
| 標準包裝： | 100 |
| 位數： | 5 |
| 數據接口： | I²C |
| 轉換器數目： | 4 |
| 電壓電源： | 單電源 |
| 工作溫度： | -40°C ~ 85°C |
| 安裝類型： | 表面貼裝 |
| 封裝/外殼： | 14-WFDFN 裸露焊盤 |
| 供應商設備封裝： | 14-TDFN-EP（3x3） |
| 包裝： | 管件 |
| 輸出數目和類型： | 4 電流，單極 |
| 采樣率（每秒）： | * |
Detailed Description
The DS4402/DS4404 contain two/four I2C adjustable
current sources (Figure 1) that are each capable of
sinking and sourcing current. Each output has 31 sink
and 31 source settings that are programmed through
the I2C interface. The full-scale ranges (and corre-
sponding step sizes) of the outputs are determined by
external resistors that adjust the output currents over a
4:1 range. The formula to determine the external resis-
tor values (RFS) for each of the outputs is given by:
Equation 1:
RFS = (VREF / IFS) x (31 / 4)
where IFS = desired full-scale current
On power-up, the DS4402/DS4404 output zero current.
This is done to prevent it from sinking or sourcing an
incorrect current before the system host controller has
had a chance to modify the device’s setting.
As a source for biasing instrumentation or other cir-
cuits, the DS4402/DS4404 provide a simple and inex-
pensive current source with an I2C interface for control.
The adjustable full-scale range allows the application to
get the most out of its 5-bit sink or source resolution.
When used in adjustable power-supply applications
(see the
Typical Operating Circuit), the DS4402/DS4404
do not affect the initial power-up supply voltage because
it defaults to providing zero output current on power-up.
As it sources or sinks current into the feedback voltage
node, it changes the amount of output voltage required
by the regulator to reach its steady state operating point.
By using the external resistor to set the output current
range, the devices provide flexibility for adjusting the
impedances of the feedback network or the range over
which the power supply can be controlled or margined.
I2C Slave Address
The DS4402/DS4404 respond to one of nine I2C slave
addresses determined by the two tri-level address
inputs. The three input states are connected to VCC,
connected to ground, or disconnected. To sense the
disconnected state (Figure 2), the address inputs have
weak internal resistors that pull the pins to mid-supply.
Table 1 lists the slave address determined by the
address input combinations.
DS4402/DS4404
Two/Four-Channel, I2C Adjustable Current DAC
_____________________________________________________________________
5
Table 1. Slave Addresses
A1
A0
SLAVE ADDRESS
(HEXADECIMAL)
GND
90h
GND
VCC
92h
VCC
GND
94h
VCC
96h
N.C.
GND
98h
N.C.
VCC
9Ah
GND
N.C.
9Ch
VCC
N.C.
9Eh
N.C.
A0h
A0
A1
I2C
ADDRESS
DECODE
RIN
VCC
RIN
Figure 2. I2C Address Inputs
相關PDF資料 |
PDF描述 |
|---|---|
| DS4412U+ | IC DAC DUAL CH I2C ADJ 8-USOP |
| DS4424N+ | IC DAC 7BIT 4CH 5.5V 14-TDFN |
| DS4425BN+ | IC OSC CLOCK 425MHZ 10-LCCC |
| DS4426T+T&R | IC DAC I2C-MARGINING 4CH 28-TQFN |
| DS4432U+ | IC DAC 7BIT 2CH 5.5V 8-MSOP |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS4404N+ | 功能描述:數模轉換器- DAC 4 Ch Adjustable RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩(wěn)定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DS4404N+T&R | 制造商:Maxim Integrated Products 功能描述:DAC 4-CH CURRENT STEERING 5-BIT 14TDFN EP - Tape and Reel 制造商:Maxim Integrated Products 功能描述:I2C ADJUSTABLE CURRENT DAC 制造商:Maxim Integrated Products 功能描述:IC DAC 4CH I2C ADJ 14-TDFN |
| DS4404N+T&R | 功能描述:數模轉換器- DAC 4 Ch Adjustable RoHS:否 制造商:Texas Instruments 轉換器數量:1 DAC 輸出端數量:1 轉換速率:2 MSPs 分辨率:16 bit 接口類型:QSPI, SPI, Serial (3-Wire, Microwire) 穩(wěn)定時間:1 us 最大工作溫度:+ 85 C 安裝風格:SMD/SMT 封裝 / 箱體:SOIC-14 封裝:Tube |
| DS4404N+TR | 制造商:MAXIM 制造商全稱:Maxim Integrated Products 功能描述:Two/Four-Channel, I2C Adjustable Current DAC |
| DS4404NR | 制造商:DALLAS 制造商全稱:Dallas Semiconductor 功能描述:Two/Four-Channel, I2C Adjustable Current DAC |
發(fā)布緊急采購，3分鐘左右您將得到回復。