- 您現在的位置：買賣IC網 > PDF目錄379184 > DS4000 RECT BRIDGE 15A 1000V WIRE LEADS PDF資料下載
參數資料
| 型號： | DS4000 |
| 英文描述： | RECT BRIDGE 15A 1000V WIRE LEADS |
| 中文描述： | 數控溫補 |
| 文件頁數： | 13/16頁 |
| 文件大?。?/td> | 227K |
| 代理商： | DS4000 |
第1頁第2頁第3頁第4頁第5頁第6頁第7頁第8頁第9頁第10頁第11頁第12頁當前第13頁第14頁第15頁第16頁
DS4000 Digitally Controlled TCXO
13 of 16
SLAVE ADDRESS
The slave address is the first byte received following the START condition generated by the master device. The
address byte consists of a 7-bit slave address and the R/
W
direction bit. The DS4000 slave address is set to
100010A
0
, where A
0
is externally hardwired to a HIGH or LOW state. This allows design flexibility to set the slave’s
address to one of two possible address locations. The last bit following the slave address is the direction bit (R/
W
)
and defines the operation to be performed by the master, transmit data (R/
W
= 0), or receive data (R/
W
= 1).
Following the START condition, the DS4000 monitors the SDA bus by checking the slave address being
transmitted. Upon receiving the proper slave address and R/
W
bit, the slave device outputs an acknowledge signal
on the SDA line regardless of the operation mode.
The DS4000 can operate in the following two modes:
1)
Slave Receiver Mode:
Serial data and clock are received through SDA and SCL. After each byte is received,
an acknowledge bit is transmitted. START and STOP conditions are recognized as the beginning and end of a
serial transfer. Address recognition is performed by the hardware after reception of the slave address and
direction bit (Figure 4).
2)
Slave Transmitter Mode:
The first byte is received and handled as in the slave receiver mode. However, in
this mode, the direction bit indicates that the transfer direction is reversed. Serial data is transmitted on SDA by
the DS4000 while the serial clock is input on SCL. START and STOP conditions are recognized as the
beginning and end of a serial transfer (Figure 5).
Figure 4. Data Write—Slave Receiver Mode
<
SLAVE ADDRESS
>
R/
W
<
DATA ADDRESS
>
<
DATA
(n)>
S
100010A
0
0
A
XXXXXXXX
A
XXXXXXXX
A
P
S = START
A = ACKNOWLEDGE
P = STOP
Figure 5. Data Read—Slave Transmitter Mode
<
SLAVE ADDRESS
>
R/W
S
100010A
0
1
A
<DATA (n)>
XXXXXXXX
<DATA (n + 1)>
XXXXXXXX
<DATA (n + 2)>
XXXXXXXX
<DATA (n + X)>
XXXXXXXX
A
A
A
A
P
S = START
A = ACKNOWLEDGE
P = STOP
A = NOT ACKNOWLEDGE
相關PDF資料 |
PDF描述 |
|---|---|
| DS4000N | RECT BRIDGE 15A 100V WIRE LEADS |
| DS4025 | RECT BRIDGE 15A 200V WIRE LEADS |
| DS4301 | Nonvolatile, 32-Position Digital Potentiometer |
| DS4301U-200 | Nonvolatile, 32-Position Digital Potentiometer |
| DS4802 | Low Voltage, Micro Power, High Performance, Rail-To-Rail Dual Op-Amp |
相關代理商/技術參數 |
參數描述 |
|---|---|
| DS4000A0/WBGA | 功能描述:TCXO振蕩器 RoHS:否 制造商:AVX 封裝 / 箱體: 頻率:32.768 kHz 頻率穩定性: 負載電容:15 pF 端接類型:SMD/SMT 電源電壓:3 V 尺寸:2.5 mm W x 3.2 mm L x 1 mm H 輸出格式:CMOS 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 封裝:Reel |
| DS4000A0N/WBGA | 功能描述:TCXO振蕩器 RoHS:否 制造商:AVX 封裝 / 箱體: 頻率:32.768 kHz 頻率穩定性: 負載電容:15 pF 端接類型:SMD/SMT 電源電壓:3 V 尺寸:2.5 mm W x 3.2 mm L x 1 mm H 輸出格式:CMOS 最小工作溫度:- 40 C 最大工作溫度:+ 85 C 封裝:Reel |
| DS4000B | 功能描述:電線導管 DS4000 BASE 10 FT. RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| DS4000C-BK | 功能描述:電線導管 DS4000 COVER MATTE BLACK - 5FT RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
| DS4000C-BZ | 功能描述:電線導管 DS4000 COVER METALLIC BRONZE -5FT RoHS:否 制造商:Panduit 類型:Slotted SideWall Open finger design wiring cut 材料:Polypropylene 顏色:Light Gray 大小: 最大光束直徑: 抗拉強度: 外部導管寬度:25 mm 外部導管高度:25 mm |
發布緊急采購，3分鐘左右您將得到回復。